Neptronic SKVF 15 Series Скачать руководство пользователя страница 30

Страница: 30 / 56

SKVF Evaporative Cooler

Installation Instructions and User Manual

www.neptronic.com

Page | 29

Sub-Menu

Setting

Default

Range

(

* indicates no configuration; display only)

Description/Notes

Physical IO

Interlock:

Closed

* (Closed, Open)

Displays the status of the interlock.
If

Open

is displayed, it indicates that the evaporative cooler is

stopped as a result of the interlock safety being open.

BinExtDemand:

* (0%, 100%)

Displays the demand value when in On/Off control mode.

(Only appears if BinDemandSrc is set to BinaryExtDemand.)

ControlInput:

Current value

* (min: 0%, max: 100%)
or
* (min: -40.0°F, max: 212.0°F)
* [min: -40.0°C, max: 100.0°C]
Units: C, F

Displays the current control input reading.

(Does not appear if ControlProfile is set to InternHumNetwork,
InternCoolNetwork, HRL Hum or HRL Cool.)
(Values are displayed in °C or °F when ControlProfile is set to
InternCoolAnalog.)

RoomRH:

Current value

* (min: 0%, max: 100%)

Displays the room humidity reading value.

(Only appears if ControlProfile is set to InternAnalog or RHSrc
is set to RoomRH.)

RoomTemp:

Current value

* (min: -40.0°F, max: 212.0°F)
* [min: -40.0°C, max: 100.0°C]
Units: C, F

Displays the room temperature reading value.

(Only appears if ControlProfile is set to InternCoolAnalog or
TempSrc is set to RoomTemp.)

SupplyHLRH:

Current value

* (min: 0%, max: 100%)

Displays the supply high limit humidity reading value.

(Only appears if ModHLProfile is set to InternAnalog or RHSrc
is set to SupplyHLRH.)

SupplyHLTemp:

Current value

* (min: -40.0°F, max: 212.0°F)
* [min: -40.0°C, max: 100.0°C]
Units: C, F

Displays the supply high limit temperature reading value.

(Only appears if ModHLProfile is set to InternCoolAnalog or
TempSrc is set to SupplyTemp.)

FanFeedBack:

Current value

* (min: 0Hz, max: 30000Hz)

Displays the feedback value from the ECM fan.

FanFeedBack2:

Current value

* (min: 0Hz, max: 30000Hz)

Displays the feedback value from the second ECM fan.

(Only applicable for SKVF-x60 models.)

FloatSwitch:

Current value

* (Inactive, Active)

Displays the status of the float switch.

(Only appears for SKVF-R models.)

WtrLeakDet:

* (Ok, Leak)

Displays whether a water leak has been detected.
If

Leak

is displayed, it indicates that there is a leak within the water

line.

RelayFuse:

Normal

* (Normal, Blown Fuse)

Displays the current status of the PCB fuse.
If

Blown Fuse

is displayed, the fuse must be replaced.

PowerFdbck:

Current value

* (min: 0%, max: 100%)

Displays the value of the power output feedback.

AlarmRelay:

Current value

* (Off, On)

Displays the status of the alarm warning relay.

ServiceRelay:

Current value

* (Off, On)

Displays the status of the service warning relay.

WaterSupplyValve:

Current value

* (Off, On)

Displays the status of the normally open water supply valve.

DrainValve:

Current value

* (Off, On)

Displays the status of the normally open drain valve.

(Only appears for SKVF-R models.)

Pump:

Current value

* (Off, On)

Displays the status of the circulation pump.

(Only appears for SKVF-R models.)

ECMFanSig:

Current value

* (min: 0V, max: 10V)

Displays the control signal value of the ECM fan.

System

SysStatus:

Operational

* (Operational, Operational Read-Only,
Download required, Download in progress,
Non-operational, Backup in progress)

Displays the current system status.

Vendor:

Neptronic

Displays the name of the vendor of the product. (Always Neptronic)

Содержание SKVF 15 Series

























































Результаты поиска

Содержание SKVF 15 Series

Отзывы:

Бренды по названию

Популярные бренды

Neptronic SKVF 15 Series, Инструкция по установке и руководство пользователя

Результаты поиска

Содержание SKVF 15 Series

Отзывы:

Бренды по названию

Популярные бренды