Neousys Technology Nuvo-7000 Series страница 59 Скачать руководство пользователя

Страница: 59 / 166

2.4.9

M.2 2280 (M Key) Slot for NVMe SSD or Optane

Memory

The system has an x4 PCIe M.2 2280 slot (also in compliance with SATA signal) for you

to install an NVMe SSD for the ultimate performance or an Intel® Optane

memory to

accelerate the read/ write performances of traditional hard disk drive. An NVMe SSD

offers exceptional performance over 2.5” SSDs while Intel® Optane

memory can

dramatically boost your traditional hard disk drives' read/ write performances.

NOTE

The M.2 slot will automatically detect and configure the slot to run PCIe or SATA signal

depending on the installed device.

Содержание Nuvo-7000 Series







































































































































































Результаты поиска

Содержание Nuvo-7000 Series

Отзывы:

Похожие инструкции для Nuvo-7000 Series

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-7000 Series, Руководство пользователя

Результаты поиска

Содержание Nuvo-7000 Series

Отзывы:

Похожие инструкции для Nuvo-7000 Series

Бренды по названию

Популярные бренды