Neousys Technology Nuvo-7000 Series страница 116 Скачать руководство пользователя

Страница: 116 / 166

116

4.1.4

SATA Configuration

The SATA controller of your system supports two (2) operating modes:

AHCI

and

Intel

RST Premium With Intel Optane System Acceleration mode

. The

AHCI

mode, which

exposes SATA's advanced capabilities such as hot swapping and native command

queuing, is supported in several later version of operating systems. The

Intel RST

Premium With Intel Optane System Acceleration

mode allows the user to greatly

accelerate SATA hard drive read/ write speeds by installing an Optane memory into the

M.2 slot. Please refer to the section “

Intel RST Premium With Intel Optane System

Acceleration”

for details.

Recommended SATA controller mode settings



If you’re using Windows 10 or Linux with kernel 4.15.18 or later, you can select

AHCI

mode for better performance.



If you are looking for faster hard drive read/ write performance, please install an SSD

(M.2, mPCIe, SATA) or install an Intel Optane memory for hard drive acceleration.

To set SATA controller mode

1. When system boots up, press F2 to enter BIOS setup utility.

2. Go to

[Advanced]

[SATA And RST Configuration]

Содержание Nuvo-7000 Series







































































































































































Результаты поиска

Содержание Nuvo-7000 Series

Отзывы:

Похожие инструкции для Nuvo-7000 Series

Бренды по названию

Популярные бренды

Neousys Technology Nuvo-7000 Series, Руководство пользователя

Результаты поиска

Содержание Nuvo-7000 Series

Отзывы:

Похожие инструкции для Nuvo-7000 Series

Бренды по названию

Популярные бренды