SECTION 3
OPERATING THE SYSTEM
40
USER GUIDE
Operation Sequence Example
This example assumes that the entire system has been properly setup to accommodate your
media, and that you will be running the system in the AUTO mode.
Refer to
Section 1 – Getting Acquainted
for the location of the switches referred to below.
The following example can be used to print a job in the Automatic (AUTO) Mode:
1. Make sure that all of the
Emergency Stop Buttons,
on all devices in the system, have
been
released
. The XPS-ProMail Base MASTER Power button will not turn on if any of
the Emergency Stop Buttons are depressed.
2. Press the
MASTER Power button,
on the XPS-ProMail Base, to turn the system
ON
(green button should remain illuminate).
3. Turn the
Printer power
switch
ON
. “Printer Offline” should appear in display.
4. On the XPS-ProMail Base Control Panel set the
Transport Base Mode
select switch to
AUTO
and the
Dryer Base Mode
select switch to
AUTO
.
Mode Switch Notes:
When the XPS-ProMail Transport Base Mode switch is set for
AUTO; the speed of the Transport Base is selected by the resolution of the print and the
belt speed selected in the printer driver and or software. If you wish to run the Transport
Base at lower speeds, then what is automatically selected by the printer, then you can set
the Transport Base Mode switch to MANUAL.
IMPORTANT!
Do NOT try to run the system faster than the maximum speed for the
selected print resolution or the printed image will be distorted.
5. If the XPS-ProDry 8.0 is installed, and you wish to use the dryer; set the
Dryer Lamp
Power
Switch
(located at the bottom, right-hand side of the dryer base) to
ON
.
6. Set
all
XPS-ProMail Base POWER
switches (Transport Base, Dryer Base and
Conveyor) to
ON
.
Tip:
Even if the optional XPS-ProDry 8.0 or TB-659 conveyor is not installed; the Dryer
Base and Conveyor POWER switches must be ON to enable the feeder control circuit.
7. Set
all
XPS-ProMail Base VACUUM
switches (Transport Base and Dryer Base) to
ON
.
8. Adjust the conveyor for the desired speed.
9. When using the
XPS-ProFeed Shuttle
Feeder, turn the Main
POWER
button
ON
(button
illuminated), set the
VACUUM
switch to the
ON
position and then set the
POWER
switch
to the
ON
position.
When using the
EasyFeed 120
or
EasyFeed 200
; switch the feeder
Power ON
and set
the
Speed Control
above zero.
10. Send Data from computer/software.
11. When you are ready to print, put the printer On-Line and press the Printer’s
ENTER
key
to begin feeding Media.
Tip:
The printer can be set to automatically start the feeder, without pressing ENTER.
See the “Automatic Feed” feature under “Menu Features”.
12. To quickly stop the entire system; Press any of the Emergency Stop buttons.
13.
To stop the feeder; press the printer’s ENTER key or turn off any of the POWER switches
on the XPS-ProMail Base.
Содержание RENA XPS-ProMail 3.0
