NeoDen IN12C Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 23

NeoDen IN12C Скачать руководство пользователя страница 9

8

4.3 Status of Indicators

There’s tri-color light on top of the cover, it is used to indicate whether all zones’

temperature have reached the well-set temperature. When all temperature reach

to well-set temperature, indicator light up green; While in the heating-up status,

indicator will flash as yellow; Only when the oven be switched off (without flash)

or in any faulty (in flash status), it will show as red .

4.4 Operation instructions

♦ Power on

Switch the button to ON status, machine start up. Please check the emergency button,

air switch and RCD before power on the machine.

♦Rail width adjustment method

The green button above the red temperature measurement interface on the left in above

picture is narrow adjustment, the green button above the blue temperature

measurement interface on the right is widening adjustment (press and hold the green

button for 3 seconds and then it automatically enters the fast width adjustment mode,

within 3 seconds for precise adjustment)

Note: In case of abnormal rail width adjustment, please adjust the width manually

by adjusting the manual adjustment handle at the back of the equipment.

Setting Transport

speed setting

Set temperature

Real-time temperature

Real-time status

Real-time power

Zone power on/ off

Power on/ off

Emergency

Width Adjustment

Button

Manual Width

Adjustment handle

«
...
7
8
9
10
11
...
»

Содержание IN12C
























Отзывы:

Нет отзывов