background image

en

    Trouble shooting

12

By hand:

Note: 

You can use a special degreaser to remove 

stubborn dirt. This can be ordered from the online shop.

Soak the metal grease filters in hot soapy water. 

Clean the filters with a brush and then rinse them 

thoroughly.

Leave the metal grease filters to drain on an 

absorbent material.

In the dishwasher:

Note: 

Slight discolouration may occur if the metal 

grease filters are cleaned in the dishwasher. This 

discolouration has no effect on the performance of the 

metal grease filters.

Use normal domestic dishwashing detergents. 

Do not clean heavily soiled metal grease filters 

together with cookware.

Place the metal grease filters in the dishwasher, 

leaving plenty of space around them. Do not trap the 

metal grease filters.

Select a temperature of no more than 70 °C.

Installing the metal mesh grease filter

:

Warning – Risk of injury! 

Components inside the appliance may have sharp 

edges. Wear protective gloves.

Note: 

Clean all accessible parts of the housing.

1.

Insert the metal grease filter and lock it in place. 

When you do this, take hold of the metal grease filter 

from underneath with your other hand.

Note: 

Make sure that the metal grease filter is 

positioned correctly.

2.

If the metal grease filter has not been inserted 

correctly, open the lock and reinsert the metal 

grease filter correctly.

3

Trouble shooting

Trouble shooting

Malfunctions often have simple explanations. Please 

read the following notes before calling the after-sales 

service.

:

Warning – Risk of electric shock! 

Incorrect repairs are dangerous. Repairs may only be 

carried out and damaged power cables replaced by 

one of our trained after-sales technicians. If the 

appliance is defective, unplug the appliance from the 

mains or switch off the circuit breaker in the fuse box. 

Contact the after-sales service.

Malfunction table

--------

LED lights

Defective LED lights may be replaced by the 

manufacturer, their customer service or a qualified 

technician (electrician) only.

:

Warning – Risk of injury! 

The light emitted by LED lights is very dazzling, and can 

damage the eyes (risk group 1). Do not look directly 

into the switched on LED lights for longer than 100 

seconds.

Problem

Possible cause Solution

The appliance 

does not work

The plug is not 

plugged in.

Connect the appliance to the 

electricity supply

Power cut

Check whether other kitchen 

appliances are working

Faulty fuse

Check in the fuse box to make 

sure that the fuse for the 

appliance is OK

The lighting does 

not work.

The LED lights 

are defective.

Call the after-sales service.

The button illumi-

nation does not 

work.

The control unit is 

faulty.

Call the after

­

sales service.

Содержание D96BMU5N0A





















Отзывы: