Necta Vending Solutions SpA Sfera, Инструкция по установке, эксплуатации и обслуживанию

Страница: 22 / 68

18
© by NECTA VENDING SOLUTIONS SpA 0404 211 - 02
0 = A or (B and C)
1 = A and B and C
2 = A and B only
3 = A and (B or C)
4 = A only
5 = A or B only (default)
6 = A or B or C
7 = A or B only
8 = A or C only
9 = B and C only
10 = B only
11 = B or C only
12 = C only
C.P.C. device
It dialogues with the coin mechanism if devices are
installed or removed from the serial interface (C.P.C.-type
devices - the monitoring unit is always enabled by default).
Minimum level of tubes
It brings forward the “Insert exact amount” message for
the user, by adding a number of coins between 0 and 15
to the programmed number of coins, to set the “full change
tubes” status.
Free Vend VMC
Most payment systems with the BDV protocol control the
free vend function.
However, there are some payment systems without such
function.
In this case, if free selections are to be dispensed, free
vending must be enabled with VMC (vending machine
control, enabled by default) and the price of the selections
must be set to zero.
MDB
The MDB protocol menus are used for defining the follow-
ing functions:
Type of vending
Setting the operating mode for multiple or single dispens-
ing. With multiple dispensing, the change is not automati-
cally returned after a successful selection, however the
credit is available for further selections. When pressing
the coin return button (if the function is enabled), the
available credit is returned up to the maximum change
value.
Change control
To enable/disable the operation of the coin return button.
Maximum credit
This function is used to define the maximum accepted
credit.
Maximum change
It is possible to set a limit to the total amount of change
returned by the coin mechanism when pressing the coin
return button or after a single dispensing serving.
Any credit exceeding the amount programmed with this
function will be cashed.
Accepted coins
It is possible to define which, among the coins recognised
by the validator, are to be accepted when the change
tubes are full.
Check the coin mechanism configuration for the correct
coin to value matching.
Returned coins
It is possible to define which, among the coins available in
the tubes, are to be used for returning the change. This
parameter is active only with coin mechanisms that do not
automatically control the choice of tube to be used (Auto
changer payout).
Check the coin mechanism configuration for the correct
coin to value matching.
Accepted bills
It is possible to define which, among the bills recognised
by the reader, are to be accepted.
Check the reader configuration for the correct bill to value
matching.
Minimum level of tubes
This function is used for setting the number of coins (0 to
15) to determine the status of full change tubes and the
“Insert exact amount” message for the user.
Accepted coins with “exact amount”
It is possible to define which, among the coins recognised
by the validator, are to be accepted when the machine is
in the “exact amount” condition.
Check the coin mechanism configuration for the correct
coin to value matching.
Accepted bills with “exact amount”
It is possible to define which, among the bills recognised
by the accepter, are to be accepted when the machine is
in the “exact amount” condition.
Check the accepter’s configuration for the correct bill to
value matching.
COMMON FUNCTIONS
Other menus are available, common to the three protocols,
used for defining the following functions:
IMMEDIATE CHANGE
Normally, the amount of credit inserted for a selection is
cashed after the machine sends the message “Selection
successful”.
When this function is enabled, disabled by default, the
cash message is sent at the beginning of dispensing.
DECIMAL POINT
Press the confirm button “ ” to display the position of the
decimal point, i.e.:
0 decimal point disabled
1 XXX.X
2 XX.XX
3 X.XXX
Press the confirm button “ ”, these values will start
blinking and can then be modified as necessary.