NEC Univerge UM8000 Скачать руководство пользователя страница 111

Страница: 111 / 130

UM8000

Issue No. 1.0

Installation Manual

13 - 5

1.4

Setting up OS/2 NetBIOS Backup For Migration

Network protocols must be installed to back up an OS/2 voice messaging
system using a NetBIOS over TCP/IP.

A NetBIOS over TCP/IP configuration is required for a an OS/2 voice
messaging system network backup. Activation or upgrade codes are not
required for network backups.

Make sure that the following installation information is available before starting
the NetBIOS backup for migration:

1.4.1

Configuring NetBIOS over TCP/IP

Configure TCP/IP and specify a Windows network domain name. If a
domain does not exist, use the procedure described in Section

1.5

Setting Up a Remote Windows Computer for a Backup on page 13-10

in this chapter.

For a network backup using NetBIOS over TCP/IP, set up the system
to log on to the network. After installing network protocols, refer to
Section

1.4.2 Setting Up an OS/2 Voice Messaging System to Log On

to a Network on page 13-8

in this chapter.

Finally, set up a Windows computer to share a drive with the OS/2
voice messaging system. Refer to Section

1.5 Setting Up a Remote

Windows Computer for a Backup on page 13-10

in this chapter.

1.4.1.1

Installing Network Protocols for a NetBIOS Backup

Log on to the OS/2 voice messaging system. The
Banner page appears.

Press

ESC

on the Banner page and follow the

system prompts.

Start an OS/2 command prompt.

On the OS/2 command prompt, type

f: <ENTER>

Subnet mask

Router

Domain name

Server name

OS/2 voice messaging system

TCP/IP address

NOTE

Set up the Windows system as a workgroup environment with a
unique TCP/IP address.

Содержание Univerge UM8000



































































































































Результаты поиска

Содержание Univerge UM8000

Отзывы:

Бренды по названию

Популярные бренды

NEC Univerge UM8000, Руководство по установке

Результаты поиска

Содержание Univerge UM8000

Отзывы:

Бренды по названию

Популярные бренды