NEC SuperScript 4600N Скачать руководство пользователя

Страница: 24 / 121

SuperScript 4600N — User’s Guide

NSTALLING

THE

ELT

ARTRIDGE

Make sure all packing materials and tape are removed
from the printer.

Open the Front Cover of the printer with the Front Cover
Release Latch (A).

Open the Top Cover of the printer by sliding the Top
Cover Release button forward (B)

Flip up the Belt Cartridge Locking Levers inside the top
of the printer (C).

Remove the Tension Release Pins from both sides of the
Belt Cartridge (D). Do not discard these pins.

Remove, but do not discard, the black protective sheet
from around the Belt Cartridge.

Slide the Belt Cartridge into the guides, as shown (E).
The flat side of the cartridge should face the front of the
printer.

Snap the Belt Cartridge Locking Levers into place (F).

Close the Top Cover and then the Front Cover of the
printer.

note:

The Belt Cartridge is sometimes called the

Photoconductor Belt Module or OPC Unit.

Caution

The Belt Cartridge should

slide easily into the printer. Do not
force it!

Save the Tension Release Pins
and black cover along with all
packing materials!

Содержание SuperScript 4600N


























































































































Результаты поиска

Содержание SuperScript 4600N

Отзывы:

Похожие инструкции для SuperScript 4600N

Бренды по названию

Популярные бренды

NEC SuperScript 4600N, Руководство пользователя

Результаты поиска

Содержание SuperScript 4600N

Отзывы:

Похожие инструкции для SuperScript 4600N

Бренды по названию

Популярные бренды