NEC POWERMATE CT 815 - RELEASE NOTES Скачать руководство пользователя

Страница: 42 / 155

System Configuration 2-15

Advanced Menu - Power Management Setup

Menu Item

Settings (default is bold)

RTC Alarm Minute

30, 0-59

Sets real time clock alarm minute (when Resume on RTC Alarm is
Enabled).

RTC Alarm Second

30, 0-59

Sets real time clock alarm second (when Resume on RTC Alarm is
Enabled).

Advanced Menu - PCI/Plug and Play Setup

Menu Item

Settings (default is bold)

Plug and Play Aware
O/S

Yes

Select No to allow the BIOS to initialize any add-on boards. Select
Yes to allow the operating system to initialize any add-on boards.

Clear NV Ram

, Yes

Select No to prohibit clearing of NV Ram.

Primary Graphics
Adapter

Auto

, Internal, External AGP, External PCI

Allows selection of the Primary Graphics Adapter as an add-on
board or as an onboard adapter.

PCI VGA Palette Snoop

Disabled

, Enabled

Set to Enabled to enable PCI VGA palette snooping.

DMA Channel
0, 1, 3, 5, 6, 7

PCI/PnP

, ISA

Permits configuring the DMA channels either by PCI/Plug and Play
or by ISA.

IRQ 3, 4, 5, 7, 9, 10, 11,
14, 15

PCI/PnP

, ISA

Permits configuring the interrupt requests either by PCI/Plug and
Play or by ISA.

Advanced Menu - Peripheral Setup

Menu Item

Settings (default is bold)

AC’97 Audio Controller

Enabled

, Disabled

The Enabled setting allows use of onboard sound.

AC’97 Modem
Controller

Enabled,

Disabled

The Enabled setting allows use of onboard telephony.

Содержание POWERMATE CT 815 - RELEASE NOTES




























































































































































Результаты поиска

Содержание POWERMATE CT 815 - RELEASE NOTES

Отзывы:

Похожие инструкции для POWERMATE CT 815 - RELEASE NOTES

Бренды по названию

Популярные бренды

NEC POWERMATE CT 815 - RELEASE NOTES, Инструкция по обслуживанию и справочник

Результаты поиска

Содержание POWERMATE CT 815 - RELEASE NOTES

Отзывы:

Похожие инструкции для POWERMATE CT 815 - RELEASE NOTES

Бренды по названию

Популярные бренды