NEC N8100-1909F Скачать руководство пользователя страница 110

Страница: 110 / 126

1. POST Error Message

Express5800/E120d-M Maintenance Guide

110

Chapter 3 Appendix

Error Message

Cause

Solution

B272

PCI Slot 2 - PCIe Link Speed

Error

PCIe bus speed error was detected
on PCI slot 2.

Contact your sales representative.

C000

The error occurred during

fan sensor reading.

An error was detected while reading
fan sensor.

C010

The error occurred during

temperature sensor reading

An error was detected while reading
temperature sensor.

C011

System Temperature out of

the range.

A temperature abnormality was
detected.

It is possible that an ambient temperature of
installation site is high, or a fan has failed or
is clogged. Contact your sales
representative.

C020

The error occurred during

voltage sensor reading.

An error was detected while reading
voltage sensor.

Contact your sales representative.

C021

System Voltage out of the

range.

A system voltage abnormality was
detected.

C040

SROM data read error

An error was detected while reading
FRU data.

C041

SROM data checksum bad

A checksum error was detected
while reading FRU data.

C061

1st SMBus device Error

detected.

An error was detected on 1st SM
Bus.

C062

2nd SMBus device Error

detected.

An error was detected on 2nd SM
Bus.

C063

3rd SMBus device Error

detected.

An error was detected on 3rd SM
Bus.

C064

4th SMBus device Error

detected.

An error was detected on 4th SM
Bus.

C065

5th SMBus device Error

detected.

An error was detected on 5th SM
Bus.

C066

6th SMBus device Error

detected.

An error was detected on 6th SM
Bus.

C067

7th SMBus device Error

detected.

An error was detected on 7th SM
Bus.

C068

8th SMBus device Error

detected.

An error was detected on 8th SM
Bus.

C101

BMC Memory Test

Failed..

An error was detected on BMC.

Unplug the power cord, wait for at least 30
seconds, then restart the server. If the same
error is detected repeatedly, contact your
sales representative.

C102

BMC Firmware Code

Area CRC check

Failed.

C103

BMC core hardware failure.

C104

BMC IBF or OBF check failed.

An error was detected while
accessing BMC.

C105

BMC SEL area full.

There is not enough space to store
the system event log.

Start up Offline Tools (

Chapter 1, 7. Offline

Tools

) and delete the event logs.

Содержание N8100-1909F































































































































Результаты поиска

Содержание N8100-1909F

Отзывы:

NEC N8100-1909F, Руководство по обслуживанию, Страница: 110 / 126

Результаты поиска

Содержание N8100-1909F

Отзывы: