NEC Express5800/E120d-1 Скачать руководство пользователя страница 65

Страница: 65 / 110

1. Installing Internal Optional Devices

Express5800/E120d-1 User’s Guide

Chapter 2 Preparations

1.8.5

Installing RAID Controller

This section describes how to install an optional RAID Controller to the slot dedicated to RAID Controller.

(1) When using the optional RAID controller (N8103-149/150/151)

For details, refer to the manual that comes with optional RAID Controller (N8103-149/150/151).

When installing more than 5 Hard Disks, K410-269(00) Intaernal SAS/SATA cable of an option is needed.

Important



You must avoid static electricity to work with the procedure below. For

details, refer to Chapter 2 (1.2 Anti-static Measures).



Do not change the mode to hibernate while building a RAID System.

Note



When installing an optional RAID Controller, start the BIOS Setup utility, select

PCI Configuration

from the

Advanced

menu, and then make sure that the

parameter of

PCI Slot xx ROM

(

is PCI slot number) is set to

Enabled



When connecting a RAID Controller, set the boot priority to 8th or higher in the

Boot menu of the BIOS Setup utility. If the setting is 9th or lower, the

configuration menu for RAID Controllers cannot be launched.

Take the following procedure to install RAID Controller (N8103-149/150/151).

Refer to steps 1 to 6 in Chapter 2 (1.3 Overview of Installation and Removal) for preparations.

Remove the two screws and remove PCI
Riser Card.

Remove the screw securing the PCI riser
card. Hold the both ends of the PCI riser
card and lift it off.

Bracket for full hight

Bracket for Low profile

Screw

Содержание Express5800/E120d-1















































































































Результаты поиска

Содержание Express5800/E120d-1

Отзывы:

Похожие инструкции для Express5800/E120d-1

Бренды по названию

Популярные бренды

NEC Express5800/E120d-1, Руководство пользователя

Результаты поиска

Содержание Express5800/E120d-1

Отзывы:

Похожие инструкции для Express5800/E120d-1

Бренды по названию

Популярные бренды