Cable
Requirements
NCR
SelfServ™
84
Walk
‐
Up
ATM
Site
Preparation
7
‐
2
REMOTE
STATUS
MONITOR
The
remote
status
monitor
feature
is
supplied
as
a
complete
assembly
consisting
of
a
status
indicator
unit,
76.2
m
(250
ft)
of
cable
and
a
connector.
Remove
a
20
mm
(0.79
in.)
section
of
the
outer
sleeve,
70
mm
(2.76
in.)
from
the
ATM
end
of
the
cable.
Take
care
not
to
cut
through
the
cable
shielding.
Shortening
the
Cable
If
you
need
to
shorten
the
cable,
proceed
as
follows:
1.
Remove
the
cover
from
the
remote
status
indicator
unit
2.
Disconnect
the
four
leads
(E1,
E2,
E3
and
E4)
from
the
indicator
3.
Cut
the
cable
to
the
required
length
and
strip
the
four
wire
ends
4.
Connect
the
wires
to
the
correct
terminals
5.
Replace
the
status
indicator
cover.
REMOTE
RELAY
CABLE
The
remote
relay
provides
a
pair
of
open
contacts,
rated
at
28
volts
per
ampere
for
both
ac
and
dc
supplies,
which
can
be
closed
to
activate
a
remote
device.
The
interconnecting
cable
to
a
remote
device
must
conform
to
the
following
specification
and
wiring:
Remove
a
20
mm
(0.79
in.)
section
of
the
outer
sleeve,
100
mm
(3.94
in.)
from
the
ATM
end
of
the
cable.
Take
care
not
to
cut
through
the
cable
shielding.
ETHERNET
STANDARD
CABLE
The
ethernet
standard
cable
must
be
fully
shielded,
8
pin,
Category
5
compliant
and
must
not
exceed
97
m
(318.20
ft)
in
length.
Remove
a
40
mm
(1.57
in.)
section
of
the
outer
sleeve,
80
mm
(3.15
in.)
from
the
ATM
end
of
the
cable.
Take
care
not
to
cut
through
the
cable
shielding.
POWER
CABLE
The
ATM
is
supplied
either
as
a
120V
or
a
220
‐
240V
unit.
120V
ATMs
are
supplied
with
a
power
cable
fitted
with
a
NEMA
type
5
‐
15P
power
source
connector.
220
‐
240V
ATMs
are
supplied
with
an
unterminated
power
cable.
Information
about
suitable
power
connectors
is
supplied
with
the
accessories.
The
power
cable
supplied
is
3
m
(9.84
ft)
in
length.
If
it
is
necessary
to
increase
this
length
to
meet
site
requirements,
then
the
extension
must
satisfy
local
or
country
regulations.
WARNING This
equipment
must
be
earthed.
70 mm
(2.76 in.)
20 mm
(0.79 in.)
(Green) E1
(Red) E2
(White) E3
(Black) E4
Red
Yellow
Green
1
2
1, 2
3
4
Rl1
RL2
1. Connector, 2 way Mate-N-Lock (NCR part no. 007-9814285).
2. Terminal wire, male (NCR part no. 007-2009663).
3. Cable, multiconductor (NCR part no. 006-5800006).
4. Connector (determined by remote device).
20 mm
(0.79 in.)
100 mm
(3.94 in.)
40 mm
(1.57 in.)
80 mm
(3.15 in.)
