P a g e
47 | 61
6.4
Maintenance performed by personnel familiar with the functional layout
of the machine and qualified for work on equipment under voltage
The following shall be performed at least once every 12 months:
- check the condition of the electrical indication and power components in the electrical
switchboard. If a fault is found, disassemble the electric switchboard and send it to a service
organization;
- check the condition of the external cabling of electric sensors and electric motors, including
connectors, cable protectors, electric distribution boxes and the mains cable. Possible faulty
parts shall be replaced;
- check the connection of the earthing cable to the earthing terminal.
6.5
Maintenance performed by personnel qualified for verification of
electrical safety of the machine
-
The machine is designed for the environment according to ČSN 33 2000-5-51 ed. 3, AA5,
AB5, AC1, AD4, AE5, AF3, AG1, AH1.
- The protection of operators of the machine against electrical shock is performed according to
ČSN EN 60 204-1 ed. 3, Art. 6.2.2, 6.2.3, 6.3.2.3, 6.3.3.
-
Installation in the point of connection to the mains must meet the requirement of ČSN 33
2000-4-41 ed. 3 Art. 411.4. Once every 3 years, regularly inspect the installation, including
the grounding wire, according to ČSN 33 2000-6 Art. 62.1.2 unless otherwise specified by
the user.
Caution:
This section contains standards used in the Czech Republic. To
verify the electrical safety of the machine and the electrical
installation of the connection point in other countries, use
updated editions of standards IEC 60 204-1 and HD 60 364-6.
- Hand over the parts washers machine with its wiring diagram and applicable user manual for
verification of its electrical equipment and installation;
- Hand over the machine with its technical documentation according to Annex 10.1 and
applicable user manual for overhaul of its electrical equipment and installation.
Regular inspection of electrical equipment of the machine
Electrical
installation of the
machine
Check of the condition and check of compliance
with documentation
Once
every 3
years
engineering
inspector
See Annex 10.1 and
User manual
Electrical
switchboard; see
Fig. 4 (pos. 4-1)
Verify the protective circuit for continuity
according to Section 18.2.2 Test 1
Electrical
measurements
according to ČSN EN
60 204-1 ed. 3
Verify the fault loop impedance according to
Section 18.2.2 Test 2
Perform the test of the lowest insulation
resistance according to ČSN EN 60204-1 ed. 3,
Article 18.3
Perform the voltage test according to Section
18.4.
Perform functional tests according to Section
18.6. Measure the maximum input power of the
machine when the wash liquid heating is
running; see Section 5.3. The input power must
not exceed the value specified in Section 3.
Содержание ADS800
