P a g e
28 | 61
Caution:
After filling the basket, close the lid again and secure it with the
closure lever against opening. When you start the machine, the
lid must be properly closed, otherwise no function can be
started!
5.3
Heating the wash liquid
After the electric circuits of the machine are switched on using the main
Q1
switch, the
P1
“ON”
signal lamp lights up and the control unit
A1
display turns on, see in Fig. 7. The heating
element starts heating up the wash liquid, and the control unit
A1
display starts displaying data
on current temperature of wash liquid. When the required maximum temperature of the wash
liquid has been reached, the control unit disconnects power supply to the heater and the
displayed temperature starts dropping until the minimum operating temperature is reached.
The heating element is activated again and the temperature starts rising. This process is
repeated until the machine is turned off.
5.3.1
Time heating
If you select the wash liquid to be heated only at a certain time, this time must be set on the
UZJ
control unit, see in Section 6.3.2, “Setting the time of activation and deactivation of time
heating”. After turning on this function in the UZJ (
dAY on
) menu, the power supply to the
heating element will be turned on and then turned off. The washing liquid will be heated only
during this time and on working days Mon - Fri.
Caution:
If the P2 “FAILURE/LEVEL” signal lamp lights up, check the
level of wash liquid (see in Section 5.8).
If the level is correct, there is a fault in the machine electric
circuits. Switch off the main switch and call a service employee!
Faults of electric circuits of the machine may only be repaired
by
personnel
with
the
corresponding
electrotechnical
qualification and acquainted with the design of the machine.
CAUTION - Danger of fatal electrical injury!
5.4 Washing cycle
Check that the
P3 “READY”
signal lamp, see in Fig. 7, is on, signalizing that the machine is
prepared for the technological processes of part washing.
Press the
SB1 “START”
button and start the washing cycle. For the time set on the control
unit, the machine is rotating and the wash liquid is sprayed on items loaded in the basket from
all spraying nozzles, as it is described in Section 2.1.4. The time remaining till the end of the
cycle is displayed on the control unit display during the cycle.
5.5
Washing interruption
If you want to terminate the washing cycle sooner for any reason, push the
SB2 “STOP”
button.
Restarting is performed using the
SB1 “START”
button, as described in the previous
paragraph. The pre-set cycle period runs again since the re-start.
Содержание ADS800
