manualshive.com logo in svg

Navien NCB-24LDWE, Руководство по установке и эксплуатации

Поделиться
Скачать
Navien NCB-24LDWE Скачать руководство пользователя страница 52

52        

M

aintaining the Boiler

I

f hot water will not flow and you suspect that the boiler is 

frozen, follow these steps:

1.  Press the Power button on the front panel to turn off the 

boiler.

2.  Close the gas valve.

Gas Valve

O

pened

Closed

3. 

O

pen the hot water tap that is closest to the boiler.

4.  Use a hair dryer or a portable electric heater to heat up both 

the pri

m

ary and secondary heat exchangers.

5.  Check every few 

m

inutes to see if water is running at the 

open tap.

6.  When the water starts flowing again, check the boiler and 

piping for leaks. 

I

f you detect any leaks or the boiler is not 

operating properly, contact an authorised technician or 
licensed professional.

Note

This boiler re

q

uires very little 

m

aintenance, however 

a 

q

ualified technician should inspect the boiler at the 

beginning of every heating season and/or when there 
is a proble

m

.

11.5    Maintenance Schedules

Owner maintenance

Daily

 

Ɣ

Check boiler area

 

Ɣ

Check pressure / te

m

perature gauge

M

onthly

 

Ɣ

Check flue piping

 

Ɣ

Check condensate drain

Periodically 

 

Ɣ

Check flue ter

m

ination screens

Every 6 

m

onths

 

Ɣ

Check boiler piping (gas and water) for 
leaks

Non-heating 

season

 

Ɣ

Shut boiler down (unless boiler used for 
do

m

estic hot water)

Service technician (See the following instructions)

Annual Start-up

General:

 

Ɣ

Address reported proble

m

s

 

Ɣ

I

nspect interior; clean and vacuu

m

 if 

necessary

 

Ɣ

Clean condensate trap and fill with fresh 
water

 

Ɣ

Check for leaks (water, gas, flue, 
condensate)

 

Ɣ

Verify flue and air lines are in good 
condition and sealed tight

 

Ɣ

Check syste

m

 piping

 

Ɣ

Check control settings

 

Ɣ

Check ignition and fla

m

e rod (clean and 

reposition)

 

Ɣ

Check wiring and connections

 

Ɣ

Fla

m

e inspection (stable, unifor

m

)

 

Ɣ

Fla

m

e signal

I

f co

m

bustion or perfor

m

ance indicate 

need:

 

Ɣ

Clean heat exchanger

 

Ɣ

Re

m

ove and clean return adapter filter

Содержание NCB-24LDWE









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды