background image

© Nauto 2019. All Rights Reserved.

4

Overview (cont.)

 WARNING 

This equipment may only be located in a position 
where it cannot interfere with the normal and safe 
operation of the vehicle, or present a hazard to 
the driver, or passengers. When routing all cables 
ensure that the insulation does not become worn 

or damaged. All cabling must be secured utilizing 
industry standard methods.

If you are unsure about the placement or 
installation of this equipment, stop work, and 
contact your Nauto representative immediately.
 
Under no circumstances should any part of the 

Nauto system be installed inside the engine 
compartment area.
 
This equipment should not be operated in 
hazardous environments, or areas that contain 

explosive materials or flammable vapors.
This equipment should not be operated in aircraft or 
in close proximity to medical equipment.

Unauthorized changes or alterations to the 
equipment may invalidate Nauto warranty, and may 
also affect the vehicle manufacturers warranty.

DISCLAIMER & SAFETY INFORMATION 

Due to ongoing development, information and specifications may change at any time without notice. While the 
information is believed to be accurate, it may include errors or inaccuracies. Nauto shall not be liable for any use of 
the installation guide or information supplied.

The installation of the Nauto Device may adversely affect other vehicle components or safety equipment. Nauto 
assumes no responsibility and disclaims any liability for any damage to any vehicle components, safety equipment, 
or bodily injury that may arise due to installation or use of Nauto’s products and services.

THE INFORMATION ON THIS INSTALLATION GUIDE IS PROVIDED “AS IS” AND TO THE EXTENT PERMITTED BY LAW, 
IS PROVIDED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY 
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR ANY PARTICULAR PURPOSE, OR NON-INFRINGEMENT. 
Nauto shall not be liable for any damages, losses, costs or expenses, direct, indirect or incidental, consequential or 
special, resulting from the use of this installation guide. 

This guide is not written for any specific vehicle since the proper wiring and installation of electronics differs for 
each vehicle. Installation should be completed by qualified individuals who are trained to wire electronics such as 
the Nauto Device. It is your responsibility to know how to wire in electronics such as the Nauto Device for your 
specific vehicle. Improper wiring may cause injury or damage and void the warranty. Any changes or modification 
to the Nauto Device not expressly approved by Nauto or the entity responsible for compliance may void any 

warranties and your authority to operate the Nauto Device.

This installation guide contains proprietary information that is protected by copyright. All rights are reserved. This 
guide may not be copied, reproduced, or translated into another language without Nauto’s prior written consent.

Содержание Nauto Device



















Отзывы: