background image

3

Nautilus

®

 LCD Installation

FCC Information

This equipment has been tested and found to comply with limits for a

class B digital device, pursuant to Part 15 of the FCC Rules. These

limits are designed to provide reasonable protection against harmful

interference in a residential installation.

This equipment can generate, uses, and radiates radio frequency

energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a

particular installation.

If this equipment does cause unacceptable interference to radio and

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures.

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment to an outlet on a circuit different from that

   to which the receiver is connected.

• Consult the dealer or an experienced Radio/TV technician for assistance.

• Any changes or modifications in construction of this device which are not expressly approved by the party responsible 

   for compliance could void the users authority to operate the equipment.

A T T E N T I O N

FCC Information

Содержание Be Strong. M-Series LCD Monitor Bracket




















Отзывы: