MoniMax 5100T 7. Appendix
7-
26
E.4 Receipt Printer
Error Code
Cause
Handling
2001000
Receipt paper jam in the receipt printer.
The jam detection sensor checks if there
is paper before starting operation.
1. Remove paper jam and paper scraps.
2. Check the lever operation position in the
sensor.
3. Check if the sensor is polluted.
4. Check if cable is cut or the connector is wrongly
inserted.
5. Check logic related to the jam detection sensor
of the Slip Printer board.
2001200
The feed lever of the recipt printer is
open.
It was detected that the feed lever was
open before ther receipt printer started to
operate.
1. Close the feed lever.
2. Check if the micro switch of the feed lever
normally functions.
3. Check if cable of the micro switch is cut in the
feed lever and the connector is wrontly inserted.
4. Check logic related to the micro switch of the
feed lever of the Slip Printer board.
2001400
The thermal head of the receipt printer is
overheated (before the receipt printer
starts to operate).
1. Check and replace the thermal printer head.
2. Check logic related to the TPH of the PR board.
2010100
Receipt printer lever opened before
printing
1. Close the lever of print head completely
2010200
TPH (Thermal Printing Head) overheated
before printing
1. Wait the time until the temperature of head
adequately slow down and try to initialize
2010300
Paper jam before printing, cutting paper
or discharging paper
1. Remove jammed paper between printer head
and rollers
2. Check and clean sensor
3. Replace sensor
2010400
Detecting no paper before printing (No
paper)
1. Replenish receipt paper
2. Check the status of sensor and its connctor
2010500
Detecting paper setting error before
printing
1. Check the status of paper setting
2. Check the sensor status and its connector
2010600
Command is received while doing self-
test
1. After terminating self-test and initialize receipt
printer
2010700
Detecting paper low (near end) before
printing
1. Replenish receipt paper
2. Check the status of Near End sensor and its
connctor
2010800 Paper
cutting
error
1. Check the Cutter module
2. Check if printer head lever is properly close
Содержание MoniMax 5100T
