background image

                                                                                                Page 12    /    26 

 

 

Mobile Home Requirements 

 

WARNING: USE OF OUTSIDE AIR IS MANDATORY WHEN INSTALLING THIS UNIT IN AN AIR TIGHT OR   

MANUFACTURED/MOBILE HOME. 

 

CAUTION: THE STRUCTURAL INTEGRITY OF THE MANUFACTURED HOME FLOOR, WALL, AND CEILING/ROOF 

MUST BE MAINTIANED. 

 

In addition to the details above, mobile home installations must meet the following requirements: 

The stove must be permanently attached to the floor. Remove the back cover, drill 2 holes through the rear of the 

base and secure with bolts or screws. Keep foot screws installed. 

The stove must be electrically grounded to the steel chassis of the mobile home with 8 AWG copper wire using an 

appropriate termination and a serrated or star washer to penetrate paint or protective coating to ensure proper 

grounding. 

The vent must be a factory-

built 3 or 4 inch listed type “L” or “PL” vent conforming to “CAN/ULC-S629, Standard For 

650C Factory-

Built Chimneys” and must extend a minimum of 36” above the roofline of the mobile home and must 

be installed using a listed ceiling fire stop and rain cap. 

When moving your mobile home, all exterior venting must be removed while the home is being relocated. After 

relocation, all venting must be reinstalled and securely fastened. 

All joints for connector pipe are required to be fastened with at least three screws and sealed with high temperature 

silicone sealant. An effective vapor barrier must be maintained wherever a chimney or other component (e.g. 

thimble) penetrates to the exterior of the home. 

CAUTION: OUTSIDE AIR IS MANDATORY FOR MOBILE HOME USE. ADEQUATE VENTILATION IS REQUIRED. 

FAILURE TO KEEP STOVE VIEWING DOOR AND ASH PAN SECURELY CLOSED OR EXCESSIVE HOME 

EXHAUST FAN OPERATION MAY CAUSE ROOM AIR STARVATION LEADING TO POSSIBLE AFFIXIATION. 

ENSURE OUTSIDE AIR INTAKE STAYS FREE FROM BLOCKAGE SUCH AS ICE, LEAVES, ETC. 

Only specified components may be used with this stove. Do not use any components that are not specified for use 

with this stove. 

Check with your local building officials as other codes may apply.

 

 

Содержание NC-40



























Отзывы: