manualshive.com logo in svg

National Instruments SCXI-1120/D, Руководство пользователя

Поделиться
Скачать
National Instruments SCXI-1120/D Скачать руководство пользователя страница 5

©

 National Instruments Corporation

v

SCXI-1120/D User Manual

Contents

About This Manual

Conventions ...................................................................................................................ix
National Instruments Documentation ............................................................................x

Chapter 1
Introduction

About the SCXI-1120/D ................................................................................................1-1
What You Need to Get Started ......................................................................................1-2
Unpacking ......................................................................................................................1-3
Software Programming Choices ....................................................................................1-3

National Instruments Application Software ....................................................1-3
NI-DAQ Driver Software ................................................................................1-4

Optional Equipment .......................................................................................................1-5

Chapter 2
Configuration and Installation

Module Configuration....................................................................................................2-1

Digital Signal Connections..............................................................................2-4

Using Jumpers W42 and W43 ..........................................................2-5
Using Jumper W44 on Revisions A and B of the SCXI-1120..........2-6
Using Jumper W44 on Revision C of the SCXI-1120 and 

All Revisions of the SCXI-1120D .................................................2-6

Analog Configuration ......................................................................................2-8

Grounding, Shielding, and Reference-Mode Selection ....................2-8
Direct Temperature Connection........................................................2-10
Gain Jumpers for the SCXI-1120/D..................................................2-10
SCXI-1120 Filter Jumpers ................................................................2-12
SCXI-1120D Filter Jumpers .............................................................2-13

Hardware Installation.....................................................................................................2-14

Chapter 3
Signal Connections

SCXI-1120/D Front Connector......................................................................................3-3
Front Connector Signal Descriptions.............................................................................3-4

Analog Input Channels ....................................................................................3-5
Temperature Sensor Connection .....................................................................3-7

SCXI-1120/D Rear Connector.......................................................................................3-8

Содержание SCXI-1120/D












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды