manualshive.com logo in svg

National Instruments SCXI-1120/D, Руководство пользователя

Поделиться
Скачать
National Instruments SCXI-1120/D Скачать руководство пользователя страница 20

Chapter 2

Configuration and Installation

SCXI-1120/D User Manual

2-6

www.natinst.com

When using a single chassis, leave W42 and W43 in position 1 on the 
SCXI-1120/D that is connected to the DAQ device. In this setting, the 
module drives MISO to SERDATOUT and connects the necessary pullup 
resistor to the SERDATOUT line. 

When using multiple chassis cabled to your DAQ device with shielded 
cables, leave jumper W42 and W43 in position 1 on the SCXI-1120/D 
modules that are connected to the DAQ device. In this setting, the module 
drives MISO to SERDATOUT and connects the necessary pullup resistor 
to the SERDATOUT line. All of the shielded adapters buffer and combine 
the SERDATOUT from each chassis to the DAQ device.

When using multiple chassis cabled to your DAQ device with ribbon 
cables, leave jumper W43 in position 1 on all of the SCXI-1120/D modules 
that are cabled to the DAQ device. Set jumper W42 to position 1 on only 
one of the SCXI-1120/D modules cabled to the DAQ device. All the other 
SCXI-1120/D modules that are cabled to the DAQ device should have 
jumper W42 in position 3. If too many pullup resistors are attached to the 
SERDATOUT line, the drivers cannot drive the line low. See Table 2-1 for 
the description and configuration of the jumper settings.

Using Jumper W44 on Revisions A and B of the 
SCXI-1120

On Revision A and B SCXI-1120 modules, the jumper is in factory-default 
position 1, which connects SLOT0SEL* to the SCXIbus INTR* line after 
buffering. In this setting, the DAQ device controls the SCXIbus INTR* 
line. See Chapter 3, 

Signal Connections

, for the pin equivalences of the 

SCXI-1120 rear signal connector and the DAQ device I/O connector.

Note

Do not use position 3. It is reserved.

Using Jumper W44 on Revision C of the SCXI-1120 
and All Revisions of the SCXI-1120D

On Revision C SCXI-1120 modules and all revisions of the SCXI-1120D 
modules, jumper W44 is not loaded, and SLOT0SEL* is always buffered 
to the INTR* line. 

Содержание SCXI-1120/D












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды