manualshive.com logo in svg

National Instruments SCXI-1120/D, Руководство пользователя

Поделиться
Скачать
National Instruments SCXI-1120/D Скачать руководство пользователя страница 27

Chapter 2

Configuration and Installation

©

 National Instruments Corporation

2-13

SCXI-1120/D User Manual

Your SCXI-1120 is shipped in the 4 Hz position. Verify that both stages are 
set to the same bandwidth to ensure that the required bandwidth is 
achieved. Notice that one jumper block is available for each filter stage.

SCXI-1120D Filter Jumpers

Two-stage filtering is also available on your SCXI-1120D module. The 
first stage is located in the isolated section of the input channel, whereas the 
second stage is located in the nonisolated section of your input channel. 
Two-stage filtering eliminates the noise generated by the isolation 
amplifier, producing a higher signal-to-noise ratio. Furthermore, two filter 
bandwidths are available, 22.5 kHz and 4.5 kHz.

Your SCXI-1120D is shipped in the 4.5 kHz position. Verify that both 
stages are set to the same bandwidth to ensure that the required bandwidth 
is achieved. Notice that one jumper block is available for each filter stage.

Table 2-7.  

SCXI-1120D Filter Jumper Allocation

Input 

Channel

Number

First

Filter Jumper

Second

Filter Jumper

4.5 kHz 

(Factory 

Default)

22.5 kHz

22.5 kHz

4.5 kHz 

(Factory 

Default)

0

W17-A

W17-B

W25

W26

1

W18-A

W18-B

W27

W28

2

W19-A

W19-B

W29

W30

3

W20-A

W20-B

W31

W32

4

W21-A

W21-B

W33

W34

5

W22-A

W22-B

W35

W36

6

W23-A

W23-B

W37

W38

7

W24-A

W24-B

W39

W40

Содержание SCXI-1120/D












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды