National Instruments SCXI-1120/D Скачать руководство пользователя

Страница: 18 / 75

Chapter 2

Configuration and Installation

2-4

www.natinst.com

Tables 2-1 to 2-2 list the description and configuration of the
user-configurable jumpers. To change the configuration of the module,
refer to Figures 2-1 and 2-2 as you perform the following steps:

Remove the grounding screw of the SCXI module top cover.

Snap out the top cover of the shield by placing a screwdriver in the
groove at the bottom of the module and pushing down.

Remove the jumpers you want to change and replace them on the
appropriate pins.

Snap the top cover back in place.

Replace the grounding screw to ensure proper shielding.

You must use software to further configure the module. Refer to your
software manual.

Figure 2-2.

Removing the SCXI Module Cover

Digital Signal Connections

The four digital signal connection jumpers have position 1 marked on the
module. Position 3 is not marked explicitly on the module.

The SCXI-1120/D has three jumpers dedicated for communication
between the DAQ device and the SCXIbus. These jumpers are W42, W43,
and W44.

Grounding

Screw

Top of Module

Front Connector

Removable Cover

Содержание SCXI-1120/D












































































Результаты поиска

Содержание SCXI-1120/D

Отзывы:

Похожие инструкции для SCXI-1120/D

Бренды по названию

Популярные бренды

National Instruments SCXI-1120/D, Руководство пользователя

Результаты поиска

Содержание SCXI-1120/D

Отзывы:

Похожие инструкции для SCXI-1120/D

Бренды по названию

Популярные бренды