manualshive.com logo in svg

National Instruments SCXI-1120/D, Руководство пользователя

Поделиться
Скачать
National Instruments SCXI-1120/D Скачать руководство пользователя страница 12

Chapter 1

Introduction

©

 National Instruments Corporation

1-3

SCXI-1120/D User Manual

Unpacking

Your SCXI-1120/D module is shipped in an antistatic package to prevent 
electrostatic damage to the module. Electrostatic discharge can damage 
several components on the module. To avoid such damage in handling the 
module, take the following precautions:

•

Ground yourself using a grounding strap or by holding a grounded 
object.

•

Touch the antistatic package to a metal part of your SCXI chassis 
before removing the module from the package.

•

Remove the module from the package and inspect the module for loose 
components or any other sign of damage. Notify National Instruments 
if the module appears damaged in any way. Do not install a damaged 
module into your SCXI chassis.

•

Never touch the exposed pins of connectors.

Software Programming Choices

There are several options to choose from when programming your National 
Instruments plug-in DAQ and SCXI hardware. You can use LabVIEW, 
LabWindows/CVI, NI-DAQ, ComponentWorks, Measure, VirtualBench, 
or register-level programming.

National Instruments Application Software

ComponentWorks contains tools for data acquisition and instrument 
control built on NI-DAQ driver software. ComponentWorks provides a 
higher-level programming interface for building virtual instruments 
through standard OLE controls and DLLs. With ComponentWorks, you 
can use all of the configuration tools, resource management utilities, and 
interactive control utilities included with NI-DAQ.

LabVIEW features interactive graphics, a state-of-the-art user interface, 
and a powerful graphical programming language. The LabVIEW Data 
Acquisition VI Library, a series of VIs for using LabVIEW with National 
Instruments devices, is included with LabVIEW. The LabVIEW Data 
Acquisition VI Library is functionally equivalent to the NI-DAQ software.

Содержание SCXI-1120/D












































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды