National Instruments NI cDAQTM-9138 Скачать руководство пользователя | Manualshive

Страница: 62 / 141

background image

© National Instruments

|

4-1

4

Digital Input/Output and PFI

This chapter describes the digital input/output (DIO) and Programmable Function Interface
(PFI) functionality available on the cDAQ chassis. Refer to the

Digital Input/Output

sections.

Digital Input/Output

To use digital I/O, insert a digital I/O C Series module into any slot on the cDAQ chassis. The
I/O specifications, such as number of lines, logic levels, update rate, and line direction, are
determined by the type of C Series I/O module used. For more information, refer to the
documentation included with your C Series I/O module(s).

Serial DIO versus Parallel DIO Modules

Serial digital I/O modules have more than eight lines of digital input/output. They can be used
in any chassis slot and can perform the following tasks:
•

Software-timed and hardware-timed digital input/output tasks

Parallel digital I/O modules can be used in any chassis slot and can perform the following tasks:
•

Software-timed and hardware-timed digital input/output tasks

•

Counter/timer tasks (can be used in up to two slots)

•

Accessing PFI signal tasks (can be used in up to two slots)

•

Filter digital input signals

Software-timed and hardware-timed digital input/output tasks have the following restrictions:
•

You cannot use parallel and serial modules together on the same hardware-timed task.

•

You cannot use serial modules for triggering.

•

You cannot do both static and timed tasks at the same time on a single serial module.

•

You can only do hardware timing in one direction at a time on a serial bidirectional module.

To determine the capability of digital I/O modules supported by the cDAQ chassis, refer to the

C Series Support in NI-DAQmx

document by going to

ni.com/info

and entering the Info

Code

rdcdaq

.

Static DIO

Each of the DIO lines can be used as a static DI or DO line. You can use static DIO lines to
monitor or control digital signals on some C Series I/O modules. Each DIO line can be

«
...
60
61
62
63
64
...
»

Содержание NI cDAQTM-9138














































































































































Отзывы:

Нет отзывов

Похожие инструкции для NI cDAQTM-9138

Бренд: Eaton Страницы: 12

Бренд: Kärcher Страницы: 4

1E0671-1 MCR2.9

Бренд: Haberl Electronic Страницы: 9

Бренд: J+J Страницы: 2

Бренд: Hunter Страницы: 2

Бренд: Tektronix Страницы: 112

Бренд: TEL Страницы: 26

Бренд: Vimar Страницы: 32

Бренд: M-system Страницы: 7

Бренд: Radionics Страницы: 18

Бренд: Renogy Страницы: 36

Бренд: SMC Networks Страницы: 15

MultiConnect Dragonfly MTQ-MNA1-B01

Бренд: Multitech Страницы: 45

Бренд: B&B PIPE & INDUSTRIAL TOOLS Страницы: 3

Thermolator TW-P

Бренд: Conair Страницы: 136

Бренд: Ultralife Страницы: 11

A Step AZ Series

Бренд: Oriental motor Страницы: 120

ID ISC.MU02.02-AD

Бренд: Feig Electronic Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды