National Instruments NI cDAQTM-9138 Скачать руководство пользователя | Manualshive

Страница: 13 / 141

background image

1-4

|

ni.com

Chapter 1

Getting Started with the cDAQ Chassis

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory requirements and limits for
electromagnetic compatibility (EMC) stated in the product specifications. These requirements
and limits provide reasonable protection against harmful interference when the product is
operated in the intended operational electromagnetic environment.

This product is intended for use in residential, commercial and industrial locations. However,
harmful interference may occur in some installations or when the product is connected to a
peripheral device or a test object. To minimize interference with radio and television reception
and prevent unacceptable performance degradation, install and use this product in strict
accordance with the instructions in the product documentation.

Furthermore, any modifications to the product not expressly approved by National Instruments
could void your authority to operate it under your local regulatory rules.

Caution

To ensure the specified EMC performance, install snap-on, ferrite bead

(National Instruments part number 711849-01, included in the shipping kit) in
accordance with the product installation instructions.

Caution

To ensure the specified EMC performance, operate this product only with

shielded cables and accessories.

Caution

To ensure the specified EMC performance, do not connect the power input

to a DC mains supply or to any supply requiring a connecting cable longer than 3 m
(10 ft). A DC mains supply is a local DC electricity supply network in the
infrastructure of a site or building.

Hardware Symbol Definitions

The following symbols are marked on your cDAQ chassis.

Caution

When this symbol is marked on a product, refer to the

Safety Guidelines

section for information about precautions to take.

EU Customers

At the end of the product life cycle, all products

must

be sent to

a WEEE recycling center. For more information about WEEE recycling centers,
National Instruments WEEE initiatives, and compliance with WEEE Directive
2002/96/EC on Waste and Electronic Equipment, visit

ni.com/environment/

weee

.

⬉ᄤֵᙃѻક∵ᶧ᥻ࠊㅵ⧚ࡲ⊩ ˄Ё೑

˅

Ё೑ᅶ᠋

National Instruments

ヺড়Ё೑⬉ᄤֵᙃѻકЁ䰤ࠊՓ⫼ᶤѯ᳝ᆇ⠽䋼ᣛҸ

(RoHS)

Ǆ݇Ѣ

National Instruments

Ё೑

RoHS

ড়㾘ᗻֵᙃˈ䇋ⱏᔩ

ni.com/

environment/rohs_china

Ǆ

(For information about China RoHS compliance,

go to

ni.com/environment/rohs_china

.)

«
...
11
12
13
14
15
...
»

Содержание NI cDAQTM-9138














































































































































Отзывы:

Нет отзывов

Похожие инструкции для NI cDAQTM-9138

Бренд: Ransburg Страницы: 49

Бренд: Balboa Страницы: 2

Бренд: Badger Meter Страницы: 20

Бренд: Uclear Страницы: 40

Бренд: Parker Страницы: 30

Compax3M Series

Бренд: Parker Страницы: 52

Бренд: Parker Страницы: 337

Бренд: u-blox Страницы: 28

Бренд: u-blox Страницы: 2

Бренд: Ultraflex Страницы: 7

Бренд: PUTCO Страницы: 2

Бренд: Vageo Страницы: 2

MagicSpeed Series

Бренд: Waeco Страницы: 76

Бренд: Brand Innovations Страницы: 56

Бренд: Valco baby Страницы: 8

TBEN-L 8IOL Series

Бренд: turck Страницы: 148

APEXpy 07-37A2-2111/ 520Series

Бренд: Bartec Страницы: 98

Бренд: Purmo Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды