National Instruments NI 9514 Скачать руководство пользователя страница 6 | Manualshive

Страница: 6 / 41

background image

NI 9514 Operating Instructions and Specifications

|

© National Instruments

|

5

Caution

The system shall be mounted in an

ATEX/IECEx-certified enclosure with a minimum ingress
protection rating of at least IP54 as defined in
IEC/EN 60079-15.

Caution

The enclosure must have a door or cover

accessible only by the use of a tool.

Electromagnetic Compatibility Guidelines

This product was tested and complies with the regulatory
requirements and limits for electromagnetic compatibility (EMC)
as stated in the product specifications. These requirements and
limits are designed to provide reasonable protection against
harmful interference when the product is operated in its intended
operational electromagnetic environment.

This product is intended for use in industrial locations. As such,
there is no guarantee that harmful interference will not occur in
a particular installation, when the product is connected to a test
object, or if the product is used in residential areas. To minimize
the potential for the product to cause interference to radio and
television reception or to experience unacceptable performance

«
...
4
5
6
7
8
...
»

Содержание NI 9514










































Отзывы:

Нет отзывов

Похожие инструкции для NI 9514

Бренд: NEC Страницы: 149

Бренд: NEC Страницы: 13

Бренд: Lawler Страницы: 6

Бренд: Data Aire Страницы: 28

Бренд: VAT Страницы: 26

Бренд: Hach Страницы: 36

Бренд: Hach Страницы: 72

Бренд: Tamas Страницы: 12

Бренд: Taoglas Страницы: 2

Бренд: Union Instruments Страницы: 63

Бренд: Parker Страницы: 4

Бренд: Danfoss Страницы: 16

Consolidated 2900-40 Series

Бренд: Baker Hughes Страницы: 80

F&G Xcomfort CRCA-00/02

Бренд: Moeller Страницы: 4

ibaMS16-DI-220V Series

Бренд: IBA Страницы: 32

Бренд: NXP Semiconductors Страницы: 39

Бренд: Digiplex Страницы: 48

Бренд: Moog Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды