National Instruments NI-488.2M Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 178

background image

Developing Your Application

Chapter 3

NI-488.2M SRM for OS/2

3-2

© National Instruments Corp.

modification. For most application programs, the NI-488 functions are
sufficient. You should use the NI-488.2 routines if you have a complex
configuration with one or more interface boards and multiple devices.
Regardless of which option you choose, the driver automatically addresses and
performs other bus management operations necessary for device communication.

The following sections discuss some differences between NI-488 functions and
NI-488.2 routines.

Using NI-488 Functions: One Device for Each Board

If your system has only one device attached to each board, the NI-488 functions
are probably sufficient for your programming needs. Some other factors that
make the NI-488 functions more convenient include the following:

•

With NI-488 asynchronous I/O functions (

ibcmda

,

ibrda

, and

ibwrta

),

you can initiate an I/O sequence while maintaining control over the CPU for
non-GPIB tasks.

•

NI-488 functions include built-in file transfer functions (

ibrdf

and

ibwrtf

).

•

The NI-488 function

ibconfig

dynamically changes the GPIB driver

configuration without the need to run the

ibconf

utility.

•

With NI-488 functions, you can control the bus in non-typical ways or
communicate with noncompliant devices.

The NI-488 functions consist of high-level (or device) functions that hide much
of the GPIB management operations and low-level (or board) functions that offer
you more control over the GPIB than NI-488.2 routines. The following sections
describe these different function types.

NI-488 Device-Level Functions

Device-level functions are high-level functions that automatically execute
commands that handle bus management operations such as reading from
and writing to devices or polling them for status. If you use device-level
functions, you do not need to understand GPIB protocol or bus management.
For information about device-level calls and how they manage the GPIB, refer to
Device-Level Calls and Bus Management, in Chapter 6, GPIB Programming
Techniques.

«
...
46
47
48
49
50
...
»

Содержание NI-488.2M



















































































































































































Отзывы:

Нет отзывов

Похожие инструкции для NI-488.2M

Бренд: 3Com Страницы: 8

Бренд: Udoo Страницы: 7

Pixie-4 Express

Бренд: XIA Страницы: 17

Бренд: mikroElektronika Страницы: 3

Бренд: Paradyne Страницы: 45

Бренд: Q-See Страницы: 2

Бренд: Zonet Страницы: 2

Бренд: Grizzly Страницы: 9

NVIP- NVRA0104/GO

Бренд: Novus Страницы: 44

Бренд: National Instruments Страницы: 130

Бренд: Cameo Страницы: 23

Бренд: ACTi Страницы: 12

Бренд: H3C Страницы: 34

Бренд: Kontron Страницы: 14

i.MX 8M Mini LPDDR4 EVK

Бренд: NXP Semiconductors Страницы: 20

Бренд: Rajant Страницы: 93

Бренд: Mobile Devices Страницы: 12

Бренд: Adeunis RF Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды