National Instruments MXI-Express x1 Series Скачать руководство пользователя страница 27

Страница: 27 / 120

Nat

ion
al
Inst

ment

Table 2-2.

MXI-Express x1 Daisy-Chain Connectivity Support From a Chassis Using a Copper Cable

From Chassis

Targets

PXI Chassis

VXI

Chassis

PXI Express Chassis

MXI-Express RIO

Slot Type

Product

NI PXI-

8360

NI PXI-

8368

NI PXI-

1033

NI VXI-

8360T

NI PXIe-

8360

NI PXIe-

1073

NI 9157

NI 9159

PXI or
PXIe Hybrid

NI PXI-8364



—

†

—

†

—

†

—

†



NI PXI-8367

—



—

PXI Express or
PXIe Hybrid

NI PXIe-8364



—



ExpressCard

‡

NI ExpressCard-8360



—



Product has an integrated MXI-Express x1 port.

†

These configurations are not supported, even though the front panel MXI connectors are mechanically compatible. For these configurations the boards

will likely report a valid cable link via the front panels LEDs. Since these link scenarios expose a possible data integrity issue that may not be obvious to
the user, National Instruments strongly recommends against using these configurations.

Daisy-chaining from PXI Express or ExpressCard slots will give better throughput and latency performance than PXI or PXI Express hybrid slots.

‡

ExpressCard slot of an embedded controller that is installed in the chassis to be daisy-chained from.

Note

: For installation instructions and other information concerning the NI PXI-1033, NI PXIe-1073, NI VXI-8360T, NI 9157, and NI 9159 refer to their

respective user manuals.

Note

: For full PXI or PXI Express functionality, refer to the

Software Installation and Configuration

section of Chapter 3,

Installation and Configuration

for more information.

Содержание MXI-Express x1 Series

























































































































Результаты поиска

Содержание MXI-Express x1 Series

Отзывы:

Похожие инструкции для MXI-Express x1 Series

Бренды по названию

Популярные бренды

National Instruments MXI-Express x1 Series, Руководство пользователя

Результаты поиска

Содержание MXI-Express x1 Series

Отзывы:

Похожие инструкции для MXI-Express x1 Series

Бренды по названию

Популярные бренды