National Instruments MXI-Express x1 Series Скачать руководство пользователя

Страница: 25 / 120

Nat

ion
al
Inst

ment

Table 2-1.

MXI-Express x1 Connectivity Support From a Host PC Using a Copper or Fiber Cable

From Host

Targets

PXI Chassis

VXI

Chassis

PXI Express Chassis

MXI-Express RIO

Slot Type

Product

NI PXI-

8360

NI PXI-

8368

NI PXI-

1033

NI VXI-

8360T

NI PXIe-

8360

NI PXIe-

1073

NI 9157

NI 9159

PCI

NI PCI-8361



—

†

—

†

—

†

—

†

—

NI PCI-8366

—



—

PCI Express x1

NI PCIe-8361



—



PCI Express x1

NI PCIe-8362



—



ExpressCard

NI Express
Card-8360



—



Industrial
Controller

NI 3100/3110



—



Product has an integrated MXI-Express x1 port.

†

These configurations are not supported, even though the front panel MXI connectors are mechanically compatible. For these configurations the boards

will likely report a valid cable link via the front panels LEDs. Since these link scenarios expose a possible data integrity issue that may not be obvious to
the user, National Instruments strongly recommends against using these configurations.

Note

: For installation instructions and other information concerning the NI PXI-1033, NI PXIe-1073, NI VXI-8360T, NI 9157, NI 9159, and the

NI 3100/3110, refer to their respective user manuals.

Note

: For full PXI or PXI Express functionality, refer to the

Software Installation and Configuration

section of Chapter 3,

Installation and Configuration

for more information.

Note

: PCI Express host slots will give better throughput and latency performance than PCI slots.

Содержание MXI-Express x1 Series

























































































































Результаты поиска

Содержание MXI-Express x1 Series

Отзывы:

Похожие инструкции для MXI-Express x1 Series

Бренды по названию

Популярные бренды

National Instruments MXI-Express x1 Series, Руководство пользователя

Результаты поиска

Содержание MXI-Express x1 Series

Отзывы:

Похожие инструкции для MXI-Express x1 Series

Бренды по названию

Популярные бренды