National Instruments mmWave Скачать руководство пользователя | Manualshive

Страница: 1 / 35

background image

USER GUIDE

mmWave OTA Validation Test
Reference Architecture

The mmWave OTA Validation Test Reference Architecture integrates mmWave signal
generation and analysis instrumentation, an anechoic chamber, a positioner, and positioner
control, providing the ability to measure the complete radiated field of the DUT in all
transmitting directions.

This manual contains hardware and software information, including step-by-step procedures
and basic information about how to begin using the mmWave OTA Validation Anechoic
Chamber and instrumentation with the mmWave OTA Validation Test Software.

Notice

The protection provided by this equipment may be impaired if it is used in

a manner not described in the documentation.

Contents

Hardware Overview.................................................................................................................. 2
Software Overview................................................................................................................... 2
Hardware Components..............................................................................................................4

mmWave OTA Validation Anechoic Chamber Exterior................................................... 4
mmWave OTA Validation Anechoic Chamber Interior.................................................... 8

Getting Started.......................................................................................................................... 8

What You Need to Get Started..........................................................................................9
Operating the Chamber................................................................................................... 10
Verifying Hardware Connections.................................................................................... 11
Performing System Calibration.......................................................................................18
Getting Started with Step-by-Step Position Sweeping................................................... 22
Getting Started With Autonomous Position Sweeping................................................... 23

Software Reference................................................................................................................. 25

Soft Front Panels.............................................................................................................25
mmWave OTA Test Visualizer........................................................................................27
OTA Measurement Interface...........................................................................................33
Antenna Plugin................................................................................................................33

Where to Go Next................................................................................................................... 34

1
2
3
...
»

Содержание mmWave




































Отзывы:

Нет отзывов

Похожие инструкции для mmWave

Бренд: NARGESA Страницы: 33

Бренд: Omnia Страницы: 8

Бренд: Yamaha Страницы: 78

Бренд: Fast Страницы: 42

Бренд: DARAY Страницы: 28

Бренд: Backyard Play Systems Страницы: 64

Бренд: Haenim Страницы: 2

Бренд: Yamaha Страницы: 46

Бренд: Pari Страницы: 12

Бренд: laerdal Страницы: 2

Бренд: laerdal Страницы: 104

Бренд: laerdal Страницы: 33

Бренд: laguna Страницы: 16

Бренд: Lafayette Страницы: 2

Бренд: LAPPSET Страницы: 16

Бренд: Nectar Страницы: 46

Бренд: Neauvia Страницы: 17

Бренд: Nederman Страницы: 255

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды