manualshive.com logo in svg

National Instruments mmWave, Руководство пользователя, Страница: 28 / 35

Поделиться
Скачать
National Instruments mmWave Скачать руководство пользователя страница 28

Window

Data Source Settings

Description

 

 

 

Data Source

Measurement File

Selects the CSV file to analyze.

Enable Auto Parsing

Enables auto update based on the timestamp of
the file to help visualize data while running.

Measurement Type

Selects the type of measurement to visualize.

Data Selection

Beam

Selects the beam.

Frequency

Selects the frequency.

Polarization

Selects the polarization.

Measurement Grid Transpose

Enables transposition if the azimuth or
elevation needs to be flipped.

Cut Analysis Tab

Use this tab to configure the cut analysis settings.

Window

Setting

Description

 

 

 

Cut Settings

Plane

Selects the cut plane.

Desired Angle

Selects the cut angle.

Lobe Detection
Settings

Beam Width Power
Reduction Level

Selects the beam width definition for
the main lobe.

Minimum Side Lobe
Detection Level

Selects the beam width definition for
the side lobes.

Plot Settings Tab

Use this tab to configure the plot settings.

Window

Setting

Description

 

 

 

Range and Scale

Display Range

Selects the range of the data to display. For
example, a range of 30 dB indicates that the
graphs display 30 dB below the maximum
number.

3D Plot Scale

Color code for 3D graphs and heat map.

Manual 3D Plot
Controls

Azimuth

Camera view settings.

Elevation

Viewing Distance

28

  | 

ni.com

  | 

mmWave OTA Validation Test Reference Architecture

Содержание mmWave




































Отзывы:

Нет отзывов