National Instruments mmWave Скачать руководство пользователя | Manualshive

Страница: 32 / 35

background image

Best Beam Index Visualization

Example

Best Beam Index (Single Beam)

Best Beam Index (All Beams)

Note

Best Beam Index (Single Beam)

displays where the selected index best peak

is found over all locations.

Best Beam Index (All Beams)

gray codes the indices for

the different selected indices. In an ideal scenario, the beam you selected should be
the best for the direction that it was intentionally created for, however, in certain
cases the index that best suits the direction is not the expected index. The
visualization makes it easier to quickly detect a problem with your codebook.

File Format for Measurement Results

You must save your measurement results as a CSV file to load them into the mmWave OTA
Test Visualizer.

Figure 6. Example File Format

•

Elevation

and

Azimuth

—Plot the measurement data with the values in these columns.

•

Frequency

—Populate this column with a valid number.

•

BeamNumber

—Customize the value of this column based on the antenna plugin.

32

|

ni.com

|

mmWave OTA Validation Test Reference Architecture

«
...
30
31
32
33
34
...
»

Содержание mmWave




































Отзывы:

Нет отзывов

Похожие инструкции для mmWave

Бренд: Falcon Страницы: 52

Бренд: MAHLE Страницы: 21

Бренд: Hanil Страницы: 60

Бренд: Banfer Страницы: 6

Бренд: Ocmis Irrigazione Страницы: 100

Бренд: Hagerman Страницы: 4

Бренд: hager Страницы: 2

TECSHOW QUAD SPIDER 60

Бренд: Ampro Страницы: 9

Бренд: Octane Fitness Страницы: 20

Бренд: Oceaneering Страницы: 27

Бренд: PAS Systems International Страницы: 24

MARK V Alcovisor

Бренд: PAS Systems International Страницы: 20

Бренд: PARRY Страницы: 14

Бренд: York Fitness Страницы: 36

Бренд: Balanced Body Страницы: 4

Бренд: Balanced Body Страницы: 2

Reformer Trapeze Combination

Бренд: Balanced Body Страницы: 164

Бренд: Wacker Neuson Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды