manualshive.com logo in svg

National Instruments mmWave, Руководство пользователя, Страница: 18 / 35

Поделиться
Скачать
National Instruments mmWave Скачать руководство пользователя страница 18

7.

Unplug the calibration laser USB cable from the USB port.

8.

Remove the laser alignment fixture from the measurement antenna fixture.

After antenna alignment is complete, you can perform system calibration and determine all the
path losses in the system.

Related Information

mmWave OTA Test Positioner SFP

 on page 25

Performing System Calibration

Use the RF System Calibration Assistant to perform a full system calibration on all the
mmWave OTA Validation Test Reference Architecture hardware components.

NI recommends performing system calibration in any of the following situations:
•

After any module in the chassis is installed, uninstalled, or moved

•

After inter-module cabling has been changed, reconnected, or repositioned

•

After changing controllers, computers, or reinstalling software

•

After self-calibration is performed on the individual instruments

The following equipment is required for the system calibration procedure:
•

PXIe-5831 Vector Signal Transceiver and mmRH-5582 mmWave Radio Head

•

Rohde & Schwarz NRP50S Power Meter

Note

 

The Rohde & Schwarz NRP50S Power Meter requires software that is not

included with the mmWave OTA Validation Test Software. Install the power meter
driver software before you complete the following steps.

1.

Connect the power meter USB cable to the PXI chassis USB port.

2.

Open the RF System Calibration Assistant and click 

Start Calibration

.

3.

In the 

Load Configuration Dialog

 dialog box, click the file button and browse to

C:\Users\Public\Public Documents\National Instruments\OTA Test
\System Calibration Files

.

4.

Select 

OTA-Test-Cal-Base.cfg

 and click 

Open

.

Note

 

The calibration configuration assumes that the name of the PXIe-5831

in Measurement & Automation Explorer (MAX) is 

3622

. If you are not using

3622

 as the name of the PXIe-5831, either change the name in the

configuration file or change it in MAX.

5.

Select 

Use existing calibration configuration

.

The 

NI RF System Calibration Assistant Configurator

 window launches.

6.

In the 

Resources

 window, verify that all resources and resource settings are correct for

the path loss characterization as shown in the following figure. Ensure the resource name
for the power meter matches the name used in MAX.

18

  | 

ni.com

  | 

mmWave OTA Validation Test Reference Architecture

Содержание mmWave




































Отзывы:

Нет отзывов