National Instruments 6711 Скачать руководство пользователя

Страница: 33 / 84

Chapter 4

Signal Connections

National Instruments Corporation

4-5

6711/6713/6715 User Manual

PFI4/GPCTR1_GATE

DGND

Input

Output

PFI4/Counter 1 Gate—As an input, this is one of the PFIs.

As an output, this is the GPCTR1_GATE signal. This signal
reflects the actual gate signal connected to the
general-purpose counter 1.

GPCTR1_OUT

DGND

Output

Counter 1 Output—This output is from the general-purpose
counter 1 output.

PFI5/UPDATE*

DGND

Input

Output

PFI5/Update—As an input, this is one of the PFIs.

As an output, this is the UPDATE* signal. A high-to-low
edge on UPDATE* indicates that the analog output
waveform generation group is being updated.

PFI6/WFTRIG

DGND

Input

Output

PFI6/Waveform Trigger—As an input, this is one of the
PFIs.

As an output, this is the WFTRIG signal. In timed analog
output sequences, a low-to-high transition indicates the
initiation of the waveform generation.

PFI7

DGND

Input

PFI7—As an input, this is one of the PFIs. PFI7 cannot be
an output.

PFI8/GPCTR0_SOURCE

DGND

Input

Output

PFI8/Counter 0 Source—As an input, this is one of the
PFIs.

As an output, this is the GPCTR0_SOURCE signal. This
signal reflects the actual source connected to the
general-purpose counter 0.

PFI9/GPCTR0_GATE

DGND

Input

Output

PFI9/Counter 0 Gate—As an input, this is one of the PFIs.

As an output, this is the GPCTR0_GATE signal. This signal
reflects the actual gate signal connected to the
general-purpose counter 0.

GPCTR0_OUT

DGND

Output

Counter 0 Output—This output is from the general-purpose
counter 0 output.

FREQ_OUT

DGND

Output

Frequency Output—This output is from the frequency
generator output.

The +5 V line on the connector of the DAQCard-6715 is fused at 0.75 A, however, the actual current available can be limited

below this value by the host computer. National Instruments recommends limiting current from this line to 250 mA.

Table 4-1.

Signal Descriptions for I/O Connector Pins (Continued)

Signal Name

Reference

Direction

Description

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 6711





















































































Результаты поиска

Содержание 6711

Отзывы:

Похожие инструкции для 6711

Бренды по названию

Популярные бренды

National Instruments 6711, Руководство пользователя

Результаты поиска

Содержание 6711

Отзывы:

Похожие инструкции для 6711

Бренды по названию

Популярные бренды