National Instruments 6711 Скачать руководство пользователя | Manualshive

Страница: 19 / 84

background image

Chapter 2

Installation and Configuration

6711/6713/6715 User Manual

2-2

www.ni.com

Note

The PXI-6711/6713 has connections to several reserved lines on the CompactPCI J2

connector. Before installing the PXI-6711/6713 in a CompactPCI system that uses J2
connector lines for a purpose other than PXI, see

Using PXI with CompactPCI

in

Chapter 1,

Introduction

.

1.

Turn off and unplug your PXI or CompactPCI chassis.

2.

Choose an unused PXI or CompactPCI peripheral slot. For maximum
performance, install the PXI-6711/6713 in a slot that supports bus
arbitration or bus-master cards. The PXI-6711/6713 contains onboard
bus-master DMA logic that can operate only in such a slot. If you
choose a slot that does not support bus masters, you will have to disable
the onboard DMA controller using your software. PXI-compliant
chassis must have bus arbitration for all slots.

3.

Remove the filter panel for the peripheral slot that you have chosen.

4.

Touch a metal part on the chassis to discharge any static electricity that
might be on your clothes or body.

5.

Insert the PXI-6711/6713 device in the 5 V slot. Use the
injector/ejector handle to fully inject the device into place.

6.

Screw the front panel of the PXI-6711/6713 to the front panel
mounting rails of the PXI or CompactPCI chassis.

7.

Visually verify the installation.

8.

Plug in and turn on the PXI or CompactPCI chassis.

The PXI-6711/6713 is now installed.

♦

PCI-6711/6713

1.

Turn off and unplug your computer.

2.

Remove the top cover or access port to the I/O channel.

3.

Remove the expansion slot cover on the back panel of the computer.

4.

Insert the 6711/6713 device into a 5 V PCI slot. Gently rock the device
to ease it into place. It can be a tight fit, but do not force the device into
place.

5.

If required, screw the mounting bracket of the 6711/6713 device to the
back panel rail of the computer.

6.

Replace the cover.

7.

Plug in and turn on your computer.

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

«
...
17
18
19
20
21
...
»

Содержание 6711





















































































Отзывы:

Нет отзывов

Похожие инструкции для 6711

Бренд: D-Link Страницы: 6

Бренд: Xilinx Страницы: 48

Бренд: StarTech.com Страницы: 10

Бренд: Component Engineering Страницы: 11

Бренд: RME Audio Страницы: 22

Бренд: TOPSCCC Страницы: 2

EZ Connect SMCWPCI-N2

Бренд: SMC Networks Страницы: 36

Бренд: GE Interlogix Страницы: 34

Бренд: GE Interlogix Страницы: 36

Бренд: Videofied Страницы: 6

Бренд: Cypress Страницы: 16

108618 - Imatumi Media Reader Card

Бренд: LaCie Страницы: 24

Бренд: QDI Страницы: 66

Бренд: Manhattan Страницы: 2

Бренд: UTC Fire and Security Страницы: 14

Бренд: Bafo Страницы: 2

XI100DE-HDMI-4K

Бренд: Magewell Страницы: 16

Бренд: Addonics Technologies Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды