National Instruments 6711 Скачать руководство пользователя

Страница: 17 / 84

Chapter 1

Introduction

National Instruments Corporation

1-7

6711/6713/6715 User Manual

Optional Equipment

National Instruments offers a variety of products to use with the 671X
device, including cables, connector blocks, and other accessories, as
follows:

•

Cables and cable assemblies

•

Connector blocks, shielded and unshielded 50- and 68-pin screw
terminals

•

RTSI bus cables

•

Low channel-count digital signal conditioning modules, devices, and
accessories

For more specific information about these products, refer to your National
Instruments catalogue or call the office nearest you.

Custom Cabling

National Instruments offers cables and accessories for you to prototype
your application or to use if you frequently change device interconnections.

If you want to develop your own cable, however, the following guidelines
can be useful:

•

Route the analog lines separately from the digital lines.

•

When using a cable shield, use separate shields for the analog and
digital halves of the cable. Failure to do so results in noise coupling
into the analog signals from transient digital signals.

Mating connectors and a backshell kit for making custom 68-pin cables are
available from National Instruments.

The following list gives recommended connectors that mate to the I/O
connector on the 6711/6713 device:

•

Honda 68-position, solder cup, female connector

•

Honda backshell

The following list gives recommended connectors that mate to the I/O
connector on the 6715 device:

•

Amp 68-position, VHDCI

•

Amp backshell

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Содержание 6711





















































































Результаты поиска

Содержание 6711

Отзывы:

Похожие инструкции для 6711

Бренды по названию

Популярные бренды

National Instruments 6711, Руководство пользователя

Результаты поиска

Содержание 6711

Отзывы:

Похожие инструкции для 6711

Бренды по названию

Популярные бренды