National Comfort Products Comfort Pack U Series, Руководство по установке

Страница: 7 / 44

7
Installation Guide | Comfort Pack with 80% Gas Heat
THE CHASSIS BASE AND EVAPORATOR DRAIN PAN, NOT
BY USING REFRIGERANT PIPING OR THE OUTDOOR FAN
MOUNT. THE BOTTOM OF THE CHASSIS IS NOT SMOOTH
AND WILL DAMAGE FLOORS IF SLID.
TO INSTALL THE CHASSIS INTO THE CABINET:
TURN OFF POWER TO THE UNIT . TEMPORARILY SECURE
THE CHASSIS POWER AND CONTROL WIRING AND TURN
OFF POWER TO THE UNIT. TEMPORARILY SECURE
THE CHASSIS POWER AND CONTROL WIRING AND
CONNECTORS TO THE TOP OF THE INDOOR COIL COVER
TO PREVENT DAMAGE DURING CHASSIS INSTALLATION.
PLACE THE OUTDOOR COIL SECTION OF THE CHASSIS
ONTO THE CABINET RAILS. LIFT THE REAR OF THE
CHASSIS USING THE EVAPORATOR COIL DRAIN PAN SO
THAT THE CHASSIS IS LEVEL AND CENTERED AS IT IS
PUSHED IN THE CABINET. DAMAGE TO THE CABINET
SEALS WILL RESULT IF THE CHASSIS IS NOT KEPT
LEVEL UNTIL THE OUTDOOR FAN COVER HAS PASSED
THE CABINET SEALS, AND IF THE CHASSIS IS NOT KEPT
CENTERED IN THE CABINET . AFTER THE CHASSIS IS ALL
THE WAY IN THE CABINET, CHECK THAT THE CHASSIS IS
CENTERED IN THE CABINET BY VERIFYING THAT IT IS IN
CONTACT WITH THE CABINET SEALS ON BOTH SIDES.
INSTALL THE INDOOR BLOWER COVER PLATE AND SECURE
IT WITH SCREWS. INSTALL THE CHASSIS POWER WIRE
CONNECTOR AND THE CONTROL WIRING CONNECTOR
INTO THEIR RESPECTIVE CABINET WIRING CONNECTORS
SO THAT THE CONNECTORS LATCH. CONNECT THE DRAIN
LINE TO THE EVAPORATOR COIL DRAIN CONNECTION.
RECONNECT 3” PIECE OF CLEAR FLEXIBLE TUBING TO
SECONDARY DRAIN ON DRAIN PAN. POSITION SECONDARY
DRAIN THROUGH GROMMET OF CHASSIS AND CONNECT
TO FLEXIBLE TUBING (PRIME TRAP PRIOR TO OPERATING).
INSTALL THE LOWER ACCESS PANEL ON THE CABINET.
TURN ON POWER TO THE UNIT.
ALL phases of this installation must comply with NATIONAL,
STATE AND LOCAL CODES. The manufacturer assumes no
responsibility for equipment installed in violation of any code
requirements.
Be sure that the electrical data specified on the unit rating
plate corresponds to what is available at the installation site
and NEC for installation requirements.
This unit MUST be installed in an outside wall for thru-the-wall
installation ONLY.
THE INSTALLATION OF THIS APPLIANCE
MUST CONFORM TO THE REQUIREMENTS
OF THE NATIONAL FIRE PROTECTION
ASSOCIATION; THE NATIONAL ELECTRIC
CODE, ANSI/NFPA NO. 70 (LATEST EDITION)
IN THE UNITED STATES; THE CANADIAN
ELECTRICAL CODE PART 1, CSA 22.1 (LATEST
EDITION) IN CANADA; AND ANY STATE OR
PROVINCIAL LAWS OR LOCAL ORDINANCES.
LOCAL AUTHORITIES HAVING JURISDICTION
SHOULD BE CONSULTED BEFORE
INSTALLATION IS MADE. SUCH APPLICABLE
REGULATIONS OR REQUIREMENTS TAKE
PRECEDENCE OVER THE GENERAL
INSTRUCTIONS IN THE MANUAL.
!
CAUTION
TO REMOVE THE CHASSIS FROM THE CABINET:
TURN OFF POWER TO THE UNIT . REMOVE THE TWO LOWER
ACCESS PANELS FROM THE CABINET. DISCONNECT
THE DRAIN LINE FROM THE EVAPORATOR COIL DRAIN
CONNECTION. DISCONNECT THE SECONDARY DRAIN
FLEXIBLE TUBING & TRAP TO AVOID DAMAGE (PRIME TRAP
WHEN REINSTALLING). DEPRESS AND HOLD THE RELEASE
LATCH ON THE CHASSIS POWER WIRING CONNECTOR
AND UNPLUG IT FROM THE CABINET POWER WIRING
CONNECTOR. DEPRESS AND HOLD THE RELEASE LATCH
ON THE CONTROL WIRING CONNECTOR AND UNPLUG IT
FROM THE CABINET CONTROL WIRING CONNECTOR.
UNFASTEN THE SCREWS ATTACHING THE INDOOR
BLOWER COVER TO THE CABINET AND REMOVE IT FROM
THE UNIT. TEMPORARILY SECURE THE CHASSIS POWER
AND CONTROL WIRING AND CONNECTORS TO THE TOP OF
THE INDOOR COIL COVER TO PREVENT DAMAGE DURING
CHASSIS REMOVAL.
CAREFULLY SLIDE THE CHASSIS OUT OF THE CABINET BY
GRASPING BOTH SIDES OF THE EVAPORATOR COIL DRAIN
PAN AND PULLING TOWARD YOU WHILE KEEPING THE
CHASSIS CENTERED IN THE CABINET. AS THE CHASSIS IS
REMOVED, KEEP THE CHASSIS LEVEL UNTIL THE OUTDOOR
FAN COVER PASSES THE CABINET SEALS. DAMAGE TO
THE CABINET SEALS WILL RESULT IF THE CHASSIS IS
NOT KEPT LEVEL UNTIL THE OUTDOOR FAN COVER HAS
PASSED THE CABINET SEALS . AFTER THE CHASSIS IS
REMOVED, IT SHOULD BE HANDLED USING