National Auto Tools NSS-8000 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 13

National Auto Tools NSS-8000 Скачать руководство пользователя страница 10

10

descent

STOP

immediately and raise until it is clear of the stop and adjust the

hemin on that latch.

Install the approach ramps on the entry side of the lift. Drive a vehicle onto the lift
tracks then install the rear wheel chocks. Run the lift up and down a few times to
insure that the latches are engaging uniformly and that the safety latch release is
functioning properly. Re-adjust if necessary.

OPERATION
Do not use this lift unless you know the proper operation of the lift and its
safety devices, and the hazards involved. See Safety Instructions page 2.

1. Drive the vehicle onto lift platform. Set the vehicle’s parking brake and leave
the transmission in park / gear. Chock the vehicle’s wheels.

2. Stand clear - Push the top UP button to raise vehicle to desired height. Push
the rod handle on the power unit to open release valve and lower tracks until it
stops, check the all four latches for full engagement in the rack on each leg.

3. To lower

– push UP button to raise – rotate latch release rod handle and hold -

push rod handle on power unit to lower. Warning: Make sure all four latches
release

– if not STOP, raise higher until latch is clear, if it does not work now the

hemin - tie rod end on that latch needs adjustment.

4. Any hydraulic oil leakage, unusual noise, or excessive wear must be fixed
before using lift.

PRE OPERATION CHECK
The user should perform daily check.

ATTENTION! LOOK OUT!

Daily check of safety

latch system is very important - the discovery of device failure before needed could save
you from expensive property damage, lost production time, serious personal injury and
even death.
1. Check safety latches for free movement and

full engagement with rack.

2. Check hydraulic connections, and hoses for leakage.
3. Check cables for damage and that they are in the groove on cable sheave.
4. Check lock collars at all rollers and sheaves.
5. Check bolts, nuts, and screws and tighten.
6. Check wiring & switches for damage.
7. Keep base plate free of dirt, grease or any other corrosive substances.

«
...
8
9
10
11
12
...
»

Содержание NSS-8000














Отзывы:

Нет отзывов