NARGESA MX700 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 41

NARGESA MX700 Скачать руководство пользователя страница 16

INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700 15

Error on lower displacement

Picture 21. Information of Error on Lower displacement

Thus, the result of the situations mentioned above, the MX700 goes into such a state that aborts any
operation being performed at that time, indicating on screen the anomalous situation that has occurred
message.

For security reasons the new activation of the punching machine is not allowed until you have removed the
abnormal situation. In case of Emergency can solve this anomalous situation by restoring the Emergency
Stop button. Once solved the corresponding anomalous situation , the punching machine restarts and
enters standby mode ( for later activation refer to paragraph 6.3. Activation of MX700).

If an error situation occurs, with intent to prevent further damage or dangerous situations for users, the
punching machine is locked, screen showing the relevant message. In this case, you can only unlock the
machine by disconnecting the voltage, and then reconnecting I again. However,at the occurrence of any
error conditions, please do not hesitate to contact Technical Support and effect so that the problem will be
solved as soon as possible.

VERIFY ENGINE

TURNIN DIRECTION

«
...
14
15
16
17
18
...
»

Содержание MX700










































Отзывы:

Нет отзывов