NARGESA MX700 Скачать руководство пользователя страница 13 | Manualshive

Страница: 13 / 41

NARGESA MX700 Скачать руководство пользователя страница 13

INSTRUCTION BOOK HYDRAULIC PUNCHING MACHINE MX700 12

5.4. Working at manual mode

In MANUAL mode, the way we work is as follows. Press the pedal to make the punching operation. By
proceeding as described here, see how the counter of the machine shown in the LCD display will be
increased in one piece.

Picture 14. Information about manual punching

Picture 14 shows how the counter now dial 1 punching operation. Once it is complete you can lift off the
foot the pedal.

You should note that this mode of operation allows you to go by descending the rod slowly as you have
more or less time down on the pedal. Upon reaching the inductive Lower displacement or when you lift your
foot off the pedal , stem movement stops.

Considering this mode of operation, you can adjust the setting of the Lower inductive to regulate the stem
descention while pressing the pedal , so you can be seeing as the machine continued its going down until
said inductive limit switch is activated.

Finally, it is important to remember that in this mode the punching rod moves ever upward , so that if you
need this up, shall proceed as detailed in the following section.

5.5. Working at automatic mode

To switch from work mode  MANUAL into AUTOMATIC work mode, all you have to do is press the AUTO
key. When doing so, the stem is activated in ascending displacement. This movement continues until the
machine has reached the  Stroke.   Moreover, the  automatic mode  is quite close to the one mentioned  in
section 6.4. However, as there are some differences, let's take a look at them:

Press the pedal to punch. By proceeding as described here, see how the counter on the machine shown in
the LCD display will be incremented by one.

Picture 15. Information of the Automatic Punching

MANUAL

CNT: 1

AUTOMATIC

CNT: 2

«
...
11
12
13
14
15
...
»

Содержание MX700










































Отзывы:

Нет отзывов