Narex ASR 200-SB BASIC, Оригинальное руководство по эксплуатации

Страница: 22 / 73

22
English
Changing the rotation direction
Using the turn direction switch (4) changes the rotation direction:
• Push down from right to left – clockwise�
• Push down from left to right – counter-clockwise�
• Button is in between – protection against accidental start�
Attention!
If you wish to change the position of the shift button, first check
that the switch button is released�
Note:
You may hear a loud click when you first use the device after
changing the rotation direction� This is normal and does not indi-
cate a problem�
Work mode set-up (ASR 200-3SB model only)
Select the work mode (work performance) by pressing and releas-
ing the switch button (3) and then repeatedly pressing the work
mode selection button (5a) on the work mode selection panel (5)�
The options for setting up individual work modes and the LED indi-
cator overview on the work mode selection panel (5) is described
below:
Work mode 1 (GREEN):
Both LED signals are turned on green (constant light)�
Suitable for tightening and loosening screw joints in the M4 to M10
range�
Maximum tightening torque: up to 120 Nm
Work mode 2 (RED):
Both LED signals are turned on red (constant light)� The device
work performance will increase by an average of up to 100 %�
Suitable for tightening and loosening screw joints in the M10 to
M20 range�
Maximum tightening torque: up to 260 Nm
Work mode 3 (AUTO MODE):
Both LED signals are blinking red and green� Allows you to gradu-
ally and safely guide a screw/bolt/self-tapping screw into material
and then tighten it quickly� Tightening speed resets automatically
according to the load from slow speed (for guiding) to the max-
imum speed (for tightening)� Suitable for construction work: in
other words, soft, as well as hard driving of screws, in combination
with the AD S12/HEX (AD-ASR 14) transfer adapter�
Maximum tightening torque: up to 260 Nm
Note:
The work mode LED indicator (5b) will automatically shut off about
1 minute after the work is finished�
Tool fastening
When mounting tools, always make sure that these attachments
are mounted on a ½” spindle (6) or to a transfer adapter all the way
(14)�
Mounting a belt clip
Place the machine on a horizontal surface (e�g� a working table)�
Slide the bent end of the belt clip (11) into the base for the belt
clip (13)� Secure the belt clip (11) using a fastening screw (12) and
a corresponding screwdriver� You can mount the belt clip to the
machine from the right, as well as the left side� Be careful not to
mount the belt clip the wrong way round� The belt clip position
must correspond to the illustration�
“RED DOTS” LED Indicator (8)
Battery charge status (capacity) indication:
Is activated automatically once you press the switch button (3)�
The LED light is on the entire time the machine is working� It turns
off immediately once the switch button is released� The following
lights up depending on the battery charge status (capacity):
• The battery is fully charged, all three status LED indicator lights
turn on�
• The battery capacity has exceeded 60 %, two red LED indicator
lights turn on (the middle and the right)�
• The battery capacity has exceeded 30 %, only one red LED in-
dicator light turns on (the right)�
Reversible defect indication
• Low battery voltage indicator – this can occur when the bat-
tery voltage nears a dangerous level, useful for its repeated,
proper and safe recharge� The control system disconnects the
engine and all the three LED indicator lights start blinking red�
Release the switch button and press it again� If the problem
persists, take the battery out of the machine and insert it into
the charger to recharge it� Place another (replacement) battery
into the machine and continue working�
• Excess load indicator – this can occur as a result of too much
power, e�g� during high torque levels, when the machine is
jammed etc� The control system disconnects the engine and
all the three LED indicator lights start blinking red� To turn the
machine on again, release the switch button and then press it
again�
• Overheating indicator – this can occur during long-term ex-
cessive use� The control system disconnects the engine and all
the three LED indicator lights start blinking red� To turn on the
machine again, you have to let it cool down� Cool down time
depends on how overheated it is�
Irreversible defect indication
May occur as a result of a combination of factors� e�g� during a
short circuit, engine failure, battery failure etc� All three LED indi-
cator lights begin blinking red� If the machine cannot be turned
on as per the above, bring it including the battery to your nearest
authorised service centre�
Table overview of problems and signals:
Problem
Reversible damage
Irreversible
damage
Voltage too low Excess load Overheating
LED indicator Blinks red Blinks red Blinks red Blinks red
Machine status Disconnected Disconnected Disconnected Disconnected
Turning the
machine on
again
Releasing and pressing the button (3)
Short-term break
to cool down
Authorised
service centre
Inserting a
charged battery
Maintenance and service
Instructions for device cleaning
Start the motor and blow impurities and dust out of the vent holes
of the device� Use protective goggles for this operation� Clean the
external plastic parts by a wet rag and mild detergent� Though
these parts are made of the materials resistant to solvents, NEVER
use any solvent�
Instructions for cleaning the charger
ATTENTION! Risk of electric shock. Prior to start han-
dling the charger, disconnect the line plug from the
socket!
Impurities and dust can be removed from external charger surfaces
by a rag or a non-metal brush� Use neither water nor detergents�
ATTENTION! With respect to protection from el. shock
and preservation of the class of protection, all mainte-
nance and service operations requesting jig saw case
removal must be performed by the authorized service
centre only!
The current list of authorized service centres can be found at our
website
www.narex.cz
, section
“Service centres”
�
Accessories
The accessories recommended for use with this device are availa-
ble commercially in the shops with hand el� tools�