
LISTENING TO AM/FM RADIO
The VISO TWO’s internal AM/FM tuner offers very high quality sound
from radio broadcasts. The reception and sound quality will always be
dependent to a degree however on the type of antenna(s) used as well as
proximity to the broadcast origin, geography and weather conditions.
ABOUT ANTENNAS
The supplied ribbon-wire FM antenna can be connected to the rear-panel
FM-antenna input using the included ‘balun’ adapter and should be fully
extended to form a “T”. This folded-dipole antenna will usually work best
when oriented vertically, with the arms of its “T” fully outstretched and
arranged perpendicular to the origin of the desired broadcast. There are
no ‘rules,’ however, and experimenting freely with antenna placement and
orientation may yield the clearest sound and lowest background noise.
In areas of poor FM reception, an exterior FM antenna can improve
performance dramatically. If radio listening is important to you, consider
consulting an antenna installation professional to optimize your system.
The supplied AM ‘loop’ antenna will usually provide adequate reception.
However, an exterior AM antenna can be used to improve reception.
Consult an antenna professional for more information.
ASSEMBLING THE LOOP ANTENNA
1
Rotate the outer frame of the antenna.
2
Insert the bottom edge of the outer frame into the groove on the stand.
3
Extend the antenna cord.
SELECTING THE RADIO
To select the VISO TWO’s tuner mode, rotate “INPUT SELECTOR” knob on the
front panel repeatedly until AM/FM mode or the HTR 6’s numeric ‘5’ while at
AMP device selector page.
Press [TUNE
/
] on the front panel momentarily to step up or down
AM or FM frequencies.
Press and hold [TUNE
/
] for more than 2 seconds to search up or
down AM or FM frequencies - the VISO TWO’s tuner will stop at the next
sufficiently strong signal it encounters. Pressing the [TUNE
/
]
during the search process will stop the search.
direct tuning
If you know your desired station’s frequency allocation, you can tune
directly to the station.
1
Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Tune” mode.
2
Using the numeric keys of the remote control, key-in the frequency
allocation of the station. For example, to enter 104.50MHz, press “1”, “0”,
“4”, “5” and “0” or press “”1”, “0”, “4” and “5”.
NOTE
Ensure that the “DEVICE SELECTOR” setting of your HTR 6 is set to
“TUNER”.
SETTING RADIO PRESET
The VISO TWO can store as many as 60 (30 FM and 30 AM stations) of your
favorite radio stations for immediate recall.
1
To store a radio preset, first tune the desired frequency (see above), then
press the front panel [MEMORY] button. The VFD will show a blinking
“MEMORY” icon and the next available vacant Preset number.
2
Press [MEMORY] button again to store the desired frequency on the
Preset number shown or use the [
/
] keys to select another
available Preset number.
3
Then, press [MEMORY] key button again. Your desired frequency is now
stored in the assigned presets.
The Radio Presets must be stored from the front panel. This setup function
is not accessible from the HTR 6 remote control.
Use the [
/
] keys on the front panel to step up or down between presets.
Press and hold [
/
] to “scroll” continuously up or down. The HTR 6 remote’s
[PRESET] keys work similarly. Empty presets will be skipped during preset tuning.
direct recall of a preSet
You can directly recall a desired Preset number.
1
Toggle [ENTER] button to switch between “Preset” and “Tune” mode (see
the lower line of the VFD). Select “Preset” mode.
2
Using the numeric keys of the remote control, directly key-in your
desired Preset number. For example, to enter Preset 5, press “5”.
NOTE
Ensure that the “DEVICE SELECTOR” setting of your HTR 6 is set to “TUNER”.
automatic preSet
Preset stations may also be programmed automatically for the entire FM (or
AM) band.
1
Toggle the [AM/FM/DB] button to select FM (or AM) band.
2
Press and hold the [MEMORY} button until the station frequency
indication begins to increase.
3
Release the button and note that the tuner will search the entire FM (or
AM) band, and stop briefly at each station that has acceptable signal
strength. The VISO TWO will automatically assign a preset number to
each station, and then search for the next station. Up to 30 of the best
received FM stations (or AM stations) will be automatically stored.
deleting a Stored preSet
You can empty a preset by deleting the stored information.
1
Select the preset number to be entered.
2
First press the [DISPLAY] button and hold it in. While holding in the
[DISPLAY] button, press the [MEMORY] button for about half a second,
then release the [MEMORY] button.
3
The preset will then be deleted and “DELETED” scrolls on the display.
4
To clear all the presets at the same time, repeat step 2 again but this
time do not release the [MEMORY] button. Hold down both buttons
until the current preset number shown in the VFD is extinguished. All
presets are now deleted.
OPERATION
uSing the viSo two - am/fm/db/ipod
EN
G
LIS
H
FR
A
N
Ç
A
IS
ES
PA
Ñ
O
L
IT
A
LIA
N
O
D
EU
TS
CH
N
ED
ER
LA
N
D
S
SV
EN
SK
A
РУ
СС
К
И
Й