![background image](http://html.mh-extra.com/html/nad/t760/t760_owners-manual_703259010.webp)
Note that an S-Video signal from Video input 1
through 3 will also be available as a Video Composite
signal on Monitor out, if the corresponding source is
selected. The composite video input signals from
Video 1 to 5 (No. 5; yellow sockets) will also be avail-
able as S-Video signal on the Monitor Out socket. If
you use both S-Video and Video composite sources,
you will only need to connect the S-Video Monitor Out
to the television or projector.
9. FRONT, CENTER & SURROUND SPEAKERS
FRONT SPEAKERS
Connect the right speaker to the terminals market
‘R +’ and ‘R -’ ensuring that the ‘R +’ is connected to
the ‘+’ terminal on your loudspeaker and the ‘R -’ is
connected to the loudspeaker’s ‘-’ terminal. Connect
the terminals marked ‘L +’ and ‘L -’ to the left speaker
in the same way.
Always use heavy duty (16 gauge; 1.5mm or thick-
er) stranded wire to connect loudspeakers to your T
760.
Unscrew the speaker terminal’s plastic bushing.
Insert the pin or bare cable end into the hole of the
terminal and then secure the cable by tightening
down the terminal’s bushing (Fig. 6).
To avoid any danger of bare metal from the speak-
er cables touching the back panel or another connec-
tor, ensure that there is only 1/2” (1.27cm) of bare
cable or pin and no loose strands of speaker wire.
NOTE:
This unit is designed to produce optimum sound
quality when speakers with impedance within the
set’s ranges are connected. Please check the follow-
ing information and choose speakers with the correct
impedance for the connections.
FRONT SPEAKERS:
4 ohms min. per speaker
CENTER SPEAKER:
4 ohms min.
SURROUND SPEAKERS: 4 ohms min. per speaker
CENTER SPEAKER
This connects the center loudspeaker that is used
when the T 760 is operated in Dolby* Digital, DTS,
Dolby Pro Logic, EARS surround sound mode or with
the 5.1 Ch. input selected.
Connect the center speaker in the same way as
described with FRONT SPEAKERS above.
SURROUND SPEAKER
This connects the Surround loudspeakers that are
used when the T 760 is operated in Dolby Digital,
DTS, Dolby Pro Logic, EARS Surround sound modes
or with the 5.1 Ch. input selected.
Connect the surround speakers in the same way as
described with FRONT SPEAKERS above.
NOTE:
The Center and/or Surround speakers must be
selected as Large or Small in the Set-up menu
“SPEAKER SELECTION” when speakers are con-
nected to these outputs. Refer also to chapter “On
Screen Display (OSD)” for more information.
10. SOFT CLIPPING
When any amplifier is driven beyond it’s power
output capabilities, a hard, distorted sound can be
heard on very loud sounds. This is caused by the
amplifier cutting off or ‘hard clipping’ the peaks of
sound that it was not designed to reproduce. The
NAD Soft Clipping circuit gently limits the output of
the system to minimize audible distortion if the ampli-
fier is overdriven.
If your listening involves moderate power levels you
may leave the Soft Clipping switch off. If you are like-
ly to play at high levels that exceed the amplifier’s
power capability, then switch Soft Clipping on.
11. NAD-LINK IN OUT
The NAD-Link connector is used to pass com-
mands from other units fitted with NAD-Link connec-
tors. This allows centralized control of a complete
system, and also allows some of the basic functions
of other NAD components (such as a CD player or
cassette deck) also equipped with NAD-Link to be
controlled with the receiver’s remote control. To func-
tion with such other units, connect the T 760’s NAD-
Link Out to the NAD-Link In on the other unit. NAD-
Link connectors can be daisy-chained, IN to OUT, so
that a whole system can be controlled from the
remote control facilities of one unit.
12. SWITCHED POWER OUTLETS
(120V North American versions only)
The AC power cords of other stereo components,
such as a CD player, may be plugged into these
accessory outlets.
Components plugged into the outlets will be
switched on and off as the T 760 is switched from
stand-by or off to on and vice versa.
NAD
10
GB