NAD
11
GB
NOTE:
The total power consumption of any components
connected to the AC outlets may not exceed 120
Watts. Never connect the mains lead of a power
amplifier to either outlets of the NAD T 760.
NOTE:
The AC outlets should be used with units with a
COMBINED power consumption of no more than 120
Watts.
13. AC POWER CORD
After you have completed all connections to the
amplifier, plug the AC line cord into a “live” wall sock-
et.
14. COOLING FAN
The cooling fan allows T 760 to deliver high
amounts of power without the unit becoming too hot.
The fan will only operate when the temperature of the
internal components starts to become hot.
NOTE:
Ensure that the air outlets of the fan aren’t blocked
in any way.
FRONT PANEL CONTROLS (Figure 2.)
1. POWER
Press the POWER button to switch the receiver to
its ‘Stand-by’ mode. The Stand-by indicator (No. 2)
over the power button will light up. On the front panel,
press any of the input selector buttons (No. 11) to
switch the receiver on. From the remote control,
press the green Stand-by button (No. 1 on remote
control drawing) to switch the unit on. The display will
light up indicating which input was selected; the
Stand-by indicator will extinguish.
Pressing the POWER switch again will turn the unit
OFF completely. The NAD T 760 receiver uses a
memory back-up system to store surround sound trim
settings and Preset station information for the tuner
section. This information is retained for several
weeks, even the unit is switched off completely or
unplugged.
REMOTE CONTROL:
STAND-BY button (green, No. 1 on remote control
drawing):
Press this button to switch the unit from operating
to the Stand-by mode and vice versa. Press this but-
ton again to switch to unit on from Stand-by; the last
selected source will be indicated in the display.
NOTE:
Stand-by mode is indicated by the Stand-by indica-
tor (No. 2) just over the green POWER button on the
front panel (No. 1).
In Stand-by mode the T 760 uses very little power.
However, it is recommended that you switch the unit
totally off if it is not going to be used for more than a
couple of days. Switch off completely by pressing the
POWER button on the front panel (No. 1), all lights
will extinguish.
Press this button to switch the unit on. To switch
the unit off, press this button again.
2. STAND-BY
This green LED will light up when the receiver is
switched On, but in Stand-by mode. Refer to section
1 in this chapter for more information.
The LED will also light up when the receiver
receives a remote control command from the sup-
plied handset.
3. DISPLAY
The T 760 supports RDS PS and RDS RT. With
stations carrying RDS information, “RDS” will light up
in the display panel, and the station’s RDS name is
automatically displayed (RDS PS).
Some radio stations, which support RDS, also
transmit additional information, known as Radio Text
(RDS RT). To view this information, use the
DISPLAY button.
With stations carrying RDS information, the DIS-
PLAY button scrolls between three different display
modes, each successive push of the button engages
the next one of the three modes:
a) In the default mode, the station’s RDS name is dis-
played, Program Service (PS; normally the sta-
tion’s calling letters, BBC R3, for instance).
b) From the default mode, press the button once to
view Radio Text (RT). This can be additional infor-
mation such as the presenter’s or program’s name;
what song is playing, etc. This text scrolls continu-
ously over the 8 alphanumeric display segments. It
takes a few seconds for the tuner to gather the RT
information, so immediately after tuning to a sta-
tion and selecting to view RT the display will indi-
cate “NO TEXT” and default to the station name. If
no RT information is available, the display will also
show “NO TEXT” for three seconds before revert-
ing to the default mode.
c) Press the button from the display RT mode to dis-
play the station frequency. Press again to return to
the default mode (a).
When the DISPLAY button is pressed when tuned
to a non-RDS station the display will show “NO
NAME” for three seconds before reverting to the
default display:
