background image

www.mycond.co.uk

6

3.Uses of the wire controller

1) ON/OFF

button. Press this button to power on and off. In the ON mode, the remote 

controller displays the operation  mode,  fan speed, ambient  temperature

 

and the humidity .

M

SET

2) The

     

button for mode selection. Press this button to choose what the mode do your want. 

( H

ffective for electric heating model)

The unit has four modes to choose from, dehumidification mode display

icon, air supply 

mode display

icon, heating mode display

icon. dehumidification plus heating mode 

display 

   

icon .   

eating mode e

M

4.Diagram of the model show

M

SET

Dehumidificationmode

M

SET

Air supply mode

Heating mode

M

SET

Dehumidification
plus heating mode

M

SET

 Defrost status. 

M

SET

M

SET

Keep flash

Keep flash

 out
    5

~45

 

Ambient temperature 

of

, the unit can

 not  properly dehumidify

1) The

     

button, after on this button , you can change the fan speed

Parameter query and 

settings.

 Press

       

3 seconds to enter parameter query setting menu.

    When display shows C1 and C3,   pressing the

       

button, parameter value is blinking, 

set the parameter value by

       

and

    

 keys  . Press the

       

button to confirm the 

modified parameters.Press the

or ON/OFF key to exit parameters setup.

SET

SET

SET

SET

Parameters C1

M

SET

Code Meaning: Weather have 
heating function . 
0: NO   1:YES   
Acquiesce :   0    

Parameters C2

Code Meaning: display the 
Condenser(coil) temperature 

M

SET

Parameters C3

Code Meaning: humidity 
sensor error .
Acquiesce :   0 %.

M

SET

Parameters C4

Code Meaning: Defrost
cycle. 
Setting range:(20min~90min)
Acquiesce :   40min.

M

SET

DEHUMIDIFIER

M

SET

Unit turn off status

Unit turn onstatus

Содержание ABS 12A




















Отзывы: