MURO VISLIDER VL42-FD Скачать руководство пользователя страница 12

Страница: 12 / 20

Preparati

-10-

Assembling the Tool

Attachment and Detachment of Rod Handle

Adjustment of Rod Handle Length

1. Loosen the handle shaft knob

completely to adjust a length of the rod
handle.

2. When the handle shaft is pulled up or

pushed down it catches slightly and
clicks at each countersink.

3. Align the knob over the countersink and

tighten it firmly.

Caution

▪

The length of the rod handle should be

adjusted with the handle attached to the
tool.

・

If the knob is tightened at a

misaligned position, the handle shaft
may be damaged making it unusable.

Attachment

Rod Handle

Handle
Shaft

Groove

Handle cover

(closed and fixed state)

The lock of
the handle
cover is
released

Rod handle
lock lever

* The lock of the handle cover

is released and the cover
opens inward by raising the
rod handle lock lever.

1. Raise and hold the rod handle lock

lever.

2. Turn the grooved side of the handle

shaft toward the lock lever. Insert the
handle shaft into the tool by pushing
down.

3. Insert the handle shaft as far as it will

go and push down on the lock lever.

Caution

Make sure that the rod handle is fixed
firmly by pulling it lightly.

Detachment

1. Lift up on the rod handle lock lever

and pull out the handle shaft.

2. Make sure that the handle cover

closes completely. Then push down
on the rod handle lock lever.

* If the handle cover is half open, raise

and lower the lock lever again to
close the handle cover completely.

Countersink

1. Loosen the knob

completely.

3. Align the knob

over the
countersink and
then tighten it
firmly.

2. Adjust the
length of the
shaft by pulling
it up or pushing
it down.

Handle shaft
stopper

Содержание VISLIDER VL42-FD





















Результаты поиска

Содержание VISLIDER VL42-FD

Отзывы:

Похожие инструкции для VISLIDER VL42-FD

Бренды по названию

Популярные бренды

MURO VISLIDER VL42-FD, Инструкция по эксплуатации

Результаты поиска

Содержание VISLIDER VL42-FD

Отзывы:

Похожие инструкции для VISLIDER VL42-FD

Бренды по названию

Популярные бренды