background image

PUSH-IN FITTING INSTALLATION

NOTE: FITTINGS AND TUBE SHOULD BE KEPT 
CLEAN, BAGGED AND UNDAMAGED PRIOR TO 
INSTALLATION.

2. Pull on the fitted tubing to ensure it is secure. Tube 

should not come free from the fitting. Water test the 
connection assembly prior to leaving the site to ensure 
there are no leaks.

DISCONNECTING THE TUBE:

To disconnect the tube from the fitting ensure that the 
water line is depressurized. Push collet square towards 
the push-in fitting body and hold. While holding the collet 
in, pull on the PE tubing to remove from the push-in fitting. 

TO CUT TUBE:

Cut to fit length of 1/4” PE tubing and remove any burrs 
or sharp edges. Ensure that the outside diameter is free 
from score marks. Tube ends should be square.

1.   Firmly and fully insert the tubing end into the push-in 

fitting up to the tube stop located approximately ½” 
deep.

INSERTING THE TUBE:

COLLET

COLLET

O-RING

O-RING

TUBE STOP

COLLET

COLLET

COLLET

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

CONTEMPORARY WATER COOLERS

 

I N S TA L L AT I O N / M A I N T E N A N C E  I N S T R U C T I O N S

 DRINKING FOUNTAINS

 

 

A152.8FG

Page 8 of 9

Revised: 

07/18/18

7020-006-001

MURDOCK  MFG.  • 

15125  Proctor  Avenue  •  City  of  Industry,  CA  91746  USA 

Phone  800-453-7465  or  626-333-2543  •  Fax  626-855-4860  •  www.murdockmfg.com

Member of

Содержание A152.8FG Series










Отзывы: