Murata DNT24 Series Скачать руководство пользователя

Страница: 42 / 84

7.4 Configuration Parameter Registers

The configuration parameters in a DNT24 module are stored in a set of variable length

registers

. Most registers are read-

write, with a few read-only or write-only. Changes made to the register settings are temporary until a

MemorySave

com-

mand is executed. Resetting or power-cycling the module will clear any changes that have not been saved to permanent
memory using the

MemorySave

command. DNT24 modules can be configured to start in protocol mode at power-up, in

which case the

EnterProtocolMode

command is not required.

7.4.1 Bank 0x00 - Transceiver Setup

Bank

Location

Name

R/W

Size

Range

Default

0x00

DeviceMode

R/W

0x01

0..2

0 (remote)

0x00

0x01

HopDuration

R/W

0x01

16..200

20 (10 ms)

0x00

0x02

ParentNwkID

R/W

0x01

0..63, 255

255 (any parent)

0x00

0x03

SecurityKey

R/W

0x10

0..2^128-1

0x00

0x13

SleepModeEn

R/W

0x01

0..2

0 (off)

0x00

0x14

WakeResponseTime

R/W

0x02

0..30000

500 (500 ms)

0x00

0x16

WakeLinkTimeout

R/W

0x01

0..255

5 (5 s)

0x00

0x17

AltParentNwkID

R/W

0x01

0..63, 255

255 (disabled)

0x00

0x18

TxPower

R/W

0x01

0..1

1 (+18 dBm)

0x00

0x19

UserTag

R/W

0x10

string

“DNT24”

0x00

0x29

RmtTransDestAddr

R/W

0x03

0x000000 (Base)

0x00

0x2C

Store&ForwardEn

R/W

0x01

0..1

0 (disabled)

0x00

0x2D

BaseModeNetID

R/W

0x01

1..63, 255

0xFF

0x00

0x2E

HeartbeatIntrvl

R/W

0x02

0..65535

0xFFFF (disabled)

0x00

0x30

SystemId

R/W

0x01

0..255

0x00

0x31

EndToEndAckEnable

R/W

0x01

0..1

0 (disabled)

0x00

0x32

LinkRetryInterval

R/W

0x02

0..65535

0 (off)

0x00

0x34

FastBeaconCount

R/W

0x02

0..65535

0 (off)

0x00

0x36

FastBeaconTrig

R/W

0x01

0..255

0 (off)

Table 7.4.1.1

DeviceMode

- this parameter selects the operating mode for the radio:

0x00 = remote (default)

0x01 = base

0x02 = router (store and forward system)

Note that changing this setting does not take effect immediately. It must be followed by a

MemorySave

command and

then either a hardware or software reset or a power off/on cycle. A router without a valid

BaseModeNetID

operates as a

remote.

HopDuration

- this parameter sets the duration of the hop frame, and can only be set on the base. The duration is an 8-bit

value, 0.5 ms/count. The valid range is from 8 to 100 ms. Changing the hop duration on the base must be followed by a

MemorySave

command to allow the change to persist through a reset or power cycle. A

HopDuration

change takes effect

immediately. Child radios will re-link following a

HopDuration

parameter change as they receive the updated hop duration

value from the base.

www.murata.com

Содержание DNT24 Series





















































































Результаты поиска

Содержание DNT24 Series

Отзывы:

Похожие инструкции для DNT24 Series

Бренды по названию

Популярные бренды

Murata DNT24 Series, Руководство по интеграции

Результаты поиска

Содержание DNT24 Series

Отзывы:

Похожие инструкции для DNT24 Series

Бренды по названию

Популярные бренды